PORCELAIN PLUS High Sheen Coating Sealer for Rough or Highly Textured Tiles

Porcelain Plus is a Professional Grade, High Performance, NanoPlus coating sealer that helps provide a high sheen to rough, highly textured tile surfaces.

• Water based, breathable (allows moisture vapour transmission)
• Scuff resistant, non-yellowing and UV resistant
• Hard wearing and durable

NanoPlus coating sealer molecules chemically bond to the rough or textured surface, creating a hard wearing, durable, high sheen film. This helps dirt and liquids clean off the surface more easily before they can stain, and adds a high sheen to the tiled surface.

Works on: rough, highly textured and hard to clean ceramic and porcelain tiles. Also adds a high sheen finish to rough, dull flat look tiles.

Where to use: domestic, commercial, indoor and outdoor areas e.g. homes, supermarkets, airports, hotels, resorts, foyers, retail stores, walkways, kitchens, restaurants, bars etc.

Test first: always test first in an inconspicuous area to determine ease of application, number of coats required, and final desired results. The end user must determine suitability of the product for their own use.

• Do not use on lightly textured, smooth or polished tile surfaces, bench tops, table tops, coffee tables etc - the coating sealer requires a rough or highly textured surface to properly bond to
• Do not use on the underside of tiles
• Not to be used in areas subject to standing or pooling water, or areas subjected to being covered with water or heavy water use e.g. showers, swimming pools, spas etc. If using outdoors, ensure adequate water run off to help prevent pooling water

1. Protective gloves, eye and skin protection
2. XtremeClean+ or Stone Wash+ to clean and prepare the surface for sealing
3. Sealer applicator, paint roller or paint pad plus a suitable plastic container or paint tray

Preparation: use XtremeClean+ or Stone Wash+ to clean and prepare the surface before sealing.

1. Sweep, vacuum or wipe the surface
2. Apply sealer to a clean, dry surface using a sealer applicator, paint roller or paint pad - minimum 2 coats
3. Ensure even coverage with a thin film coat - do not apply thick or heavy coats. Apply thin even coats for the best final result
4. Avoid overworking the product to help avoid air bubbles and drag marks
5. "Feather" back to remove excess sealer and streak marks to leave a thin even film with no streak marks or puddling
6. Apply the next coat as soon as the previous coat is dry to the touch - minimum 30 minutes between coats
7. Apply the next coat crossways to the previous application e.g. 1st coat in a north-south direction and 2nd coat in an east-west direction
8. Minimum 2 thin coats. Apply more coats until the desired level of gloss is reached. When applying subsequent coats, repeat steps 2-7
9. The surface is ready for light traffic when dry (minimum 6 hours). Keep the surface dry for a minimum of 24 hours. Full cure in 24-48 hours

Tip: if further slip resistance is required, add Grip-It Powder (anti-slip powder additive) to the final coat.

Approximately 40-60 m² per 4 litres per coat. Coverage will vary depending on the porosity and texture of the surface, plus weather conditions, the application method and number of coats required.

Sealer is not a waterproofing agent and will not prevent surface wear or etching from harsh or acidic chemicals. Wipe spills as soon as possible to help reduce staining and slip falls.

Expected wear will vary depending on surface texture and hardness, traffic wear plus the frequency and type of cleaning products used. Harsh cleaning including pressure washing, high alkaline, acidic or solvent-based cleaners and/or weather exposure will affect wear and performance. High traffic and exterior areas will require more frequent re-application. Re-seal as necessary.

Apply additional coats of Porcelain Plus over time as required. Only use EzyClean+ for routine, everyday/weekly cleaning and disinfecting. It is an easy to use, rinse free and streak free, concentrated pH neutral cleaner that does not affect the coating sealer.

How to remove: use Aqua-Strip or Strip-It as per label instructions to remove Porcelain Plus.

• Read the entire label, SDS and technical bulletin before using
• Wear appropriate gloves, skin and eye protection
• Use when the surface temperature is between 4°C and 28°C
• Surface must be clean, dry and free from sealers and coatings
• Do not allow sealer to drip or leave drip marks
• Do not saturate open grout joints before grouting if using as a pre-sealer. Alternatively, you can use Grout Release+ as a pre-grouting coating to help make the grouting clean up process easier
• If the coating is subjected to water coverage, pooled water or incompatible cleaners it may turn white or cloudy
• Avoid dragging furniture across the coating sealer to help avoid scratches or damage to the coating

Handling & storage: close the container tightly after each use. Store in the original container between 4°C and 32°C. Shelf life is approximately 3 years in an unopened container - less after opening. Storage beyond that time does not necessarily mean the product is not usable - do a small test area first. Do not re-use the container; discard in rubbish. Clean tools and clothing with water before they dry.

First aid: contact the Poisons Information Centre (Australia Ph: 131-126, NZ Ph: 0800 764-766). Avoid contact with skin and eyes. Do not swallow; if swallowed do not induce vomiting and rinse mouth well with water. If in eyes, hold eyelids apart and immediately flush the eye with clean, running water for at least 15 minutes and see a doctor. If on skin, wash thoroughly with water. If feeling unwell, seek medical attention.