ENHANCE'N'SEAL To Seal and Enhance The Colour of Stone, Terrazzo, Encaustics etc

Enhance'N'Seal is a Professional Grade, Premium, 100% Actives, Low VOC, below surface, breathable, penetrating type sealer and colour enhancer. NanoPlus formula penetrates deeper, then chemically bonds to help provide maximum stain resistance against oil, food, grease and grime. Also helps enhance, darken and rejuvenate colour for a no sheen, darker, colour enhanced look. Safe for food preparation areas.

NanoPlus sized sealing molecules penetrate deep into the surface, then chemically bond and reduce the size of the open pores, therefore reducing porosity. Liquids can then be easily wiped from the surface before they stain. Spills should be wiped up immediately to help minimise staining. Helps provide maximum stain resistance against oil, food, grease and grime.

Works on: all porous natural stone (e.g. basalt, bluestone, granite, marble, limestone, quartz, sandstone, slate, travertine etc), encaustic, terrazzo and quarry tiles, bricks, saltillo, terracotta, concrete, pavers, cement render etc, for a no sheen, darker, colour enhanced look and maximum stain resistance.

Where to use: walls, floors, bench-tops, facades etc in domestic, commercial, indoor and outdoor areas e.g. homes, supermarkets, airports, hotels, resorts, foyers, walkways, driveways, kitchens, restaurants, bars etc.

Test first: always test first in an inconspicuous area to determine ease of application, coats required, colour stability and desired results. The end user must determine suitability of the product for their own use.

1. Read entire label, SDS and technical bulletin before using
2. Wear appropriate gloves, skin, eye and foot protection
3. Use when surface temperature is between 4\u00b0C and 32\u00b0C
4. Surface must be clean, dry and free from other sealers and coatings
5. Do not allow sealer to drip or leave drip marks
6. Do not use on the underside of the tile or stone. If six sided/dip sealing is required, use Condense Plus first. It will help strengthen, consolidate and densify the surface
7. Once the surface has been colour enhanced it cannot be restored back to the original look

Preparation: use either XtremeClean+ or Stone Wash+ as per label instructions to clean and prepare the surface before sealing.

What you need before you start:

1. Mask, protective gloves, eye, skin and foot protection
2. Sealer applicator, sealer sponge, brush, paint roller or paint pad plus a suitable container/paint tray for the product
3. Plenty of clean absorbent cloth or cotton towels or paper towels
4. XtremeClean+ or Stone Wash+ to clean and prepare the surface

For quick and easy clean-up after grouting, as porous surfaces may stain during install and grouting.

1. Pre-seal the surface before installing, or 24-48 hours after installation (must be completely dry before pre-sealing surface)
2. Do not saturate the open grout joints
3. Allow a minimum of 24 hours cure time before grouting
4. If using dark or contrasting grout, or grouting porous rough textured surfaces, apply Grout Release+ after Enhance'N'Seal has cured, then grout as usual

1. Apply sealer to a clean, dry surface using a sealer applicator, sealer sponge, brush, paint roller or paint pad
2. Ensure an even coat and coverage, then work the product in thoroughly
3. After 10-15 minutes, wipe the surface completely dry with absorbent paper or cotton towels to remove any excess
4. Do not allow the product to dry on the surface - add more product to keep it wet for the 10-15 minutes
5. Repeat this process for each application

Quick guide for sealing:

1. Pour into a suitable sized container
2. Apply sealer to the surface and work it in
3. After 10-15 minutes wipe surface completely dry

Application notes:

1. For vertical surfaces apply bottom to top and avoid run-down
2. Porous surfaces will require additional coats. If 2 or more coats are required, allow a minimum of 30 minutes between coats
3. 2 hours after the final coat, conduct a test to determine if the surface is properly sealed. Apply a few water droplets. If water is easily absorbed, apply an additional coat of sealer. Wait 2 hours and repeat the test
4. The surface is ready for light traffic after 2 hours. Keep dry for a minimum of 48 hours. Full cure in a minimum of 48 hours

Approx 8-40 m\u00b2 per litre per coat (minimum 2 coats recommended). Will vary depending on the density, porosity, texture and absorption of the surface, plus weather conditions, application method and number of coats required. Table below as a guide (per 1 L per 1 coat). Full coverage chart at sealersplus.com.au.

Limitations: not a waterproofing agent and will not prevent surface wear, scuff marks or etching from harsh or acidic products. Spills should be wiped up immediately to help minimise staining.

Other sealer options: if a natural look is desired, use Aqua-Seal Gold+. If a gloss film finish is desired, use Gloss'N'Seal.

Expected wear: will vary depending on surface texture and hardness, traffic wear plus frequency and type of cleaning products used. Harsh cleaning including pressure washing, high alkaline, acidic or solvent-based cleaners and/or weather exposure will affect wear and performance. High traffic and exterior areas will require more frequent re-application. Re-seal as necessary.

• EzyClean+ for routine, everyday cleaning plus disinfecting
• XtremeClean+ for periodic heavy duty cleaning and disinfecting

Handling, storage and clean up: close the container tightly after each use. Store in the original container between 4\u00b0C and 28\u00b0C. Shelf life is approx 1 (one) year in an unopened container - less after opening. Product may harden or gel in the container if not stored correctly or past shelf life. Storage beyond that time does not necessarily mean the product is not usable - do a small test area first. Do not re-use the container; discard in rubbish. Clean tools with mineral spirits before they dry.

First aid: contact a doctor or Poisons Information Centre (Aust 131-126, NZ 0800 764 766). If in eyes, hold eyelids apart and flush continuously with running water until advised to stop or for at least 15 minutes. If skin or hair contact occurs, remove contaminated clothing and flush skin or hair with running water. If inhaled, remove to fresh air. If ingested, wash mouth with water. Do not induce vomiting.