HOW TO CLEAN WALLS & FLOORS WITH ACTIVE PLUS

Step-by-step instructions for natural stone, ceramic, porcelain, encaustic and terrazzo tiles, concrete, grout, pavers and bricks on walls and floors, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Cleaning walls + floors

Pre-wet, apply, keep wet, scrub, rinse

Active Plus is an easy to use, 100% actives, super concentrated, triple action oxygen cleaner, deodoriser and stain remover. Mixed with warm water, it helps remove algae, mould, mildew, leaf and tannin stains, dirt and grime. It is non-acidic, so it is suitable for acid-sensitive surfaces.

  • Powder, mixed with warm water: General Cleaning 30 g per 1 L, Heavy Duty 60 g per 1 L, Extreme up to 120 g per 1 L
  • Walls: pre-wet the wall and the ground below it, apply from the bottom up, rinse from the top down
  • Floors: apply with a clean mop, remove the dirty solution with a wet vac, then rinse
  • Allow 10–15 minutes dwell time. Add more solution to keep it wet: don't let it dry on the surface
  • Protect plants, soil and metals. Always test first
  • Stubborn, deep-set stains: use the stain removal (paste) method
  • Keep away from non-recommended surfaces
Active Plus 2 kg
ACTIVE PLUS
300 g · 1 kg · 2 kg
$72.00 View product

Which strength do I need?

Active Plus is a powder that you mix with warm water and use as a cleaning solution on walls and floors. Start with the strength that suits the job:

  • General Cleaning, 30 g per 1 litre: light or fresh soiling and stains
  • Heavy Duty, 60 g per 1 litre: heavier or older soiling and stains
  • Extreme, up to 120 g per 1 litre: the worst stains

How well a surface cleans up depends on the surface, the type of soiling or stain, how long it has been there and whether the surface was sealed. Always do a test area first.

TIP: once the surface is clean and completely dry, seal porous surfaces with Aqua-Seal Gold+® for a natural look or Enhance'N'Seal for a colour enhanced look, to help reduce future staining and make cleaning easier.

Before cleaning: sandstone wall and paving

Before cleaning: sandstone wall and paving

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Plants, soil and metals (keep it away)
  • Painted or timber surfaces (protect them)
  • Etch marks or dull, damaged polish: it won't remove etching or restore polish

What you'll need

  • Active Plus
  • Scrubbing pads: white (light), blue (moderate) and black (heavy), with the Scrub'N'Clean Kit - Walls (walls) or a Scrub'N'Clean Kit, Strip'N'Clean Kit or broom (floors)
  • Good quality stiff bristle brush for rough or heavily textured surfaces
  • Plastic bucket and warm/hot water (not boiling)
  • Kitchen scales or a measuring cup
  • Walls: sponge or soft brush to apply the solution. Floors: clean mop
  • Hose or bucket of clean water for pre-wetting and rinsing
  • Wet vac (recommended) to pick up the dirty solution and run-off
  • Plastic sheet to cover plants, soil and metal fixtures
  • Gloves, eye, skin and foot protection

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C. Work out of direct hot sun and wind so the surface stays wet
  • Cover plants, soil and metals, and protect painted or timber surfaces
  • Sweep away leaves and debris
  • Mix only what you'll use: never cover or store mixed solution
  • Mix only what you'll use: never cover or store the mixed solution in a sealed container
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Protect and pre-wet: wallsWALLS
Protect and pre-wet: floorsFLOORS
1Prepare

Protect and pre-wet

Cover plants, soil, metal fixtures and anything painted or timber nearby. Sweep away leaves and debris. Walls: pre-wet the wall and the ground below it with clean water, so run-off doesn't soak in and leave streaks. Floors: pre-wet the surface with clean water.

Do a test area first: wallsWALLS
Do a test area first: floorsFLOORS
2Prepare

Do a test area first

VERY IMPORTANT
Try the solution on a small, hidden spot to check surface colour stability and results.

Mix Active Plus: wallsWALLS
Mix Active Plus: floorsFLOORS
3Treat

Mix Active Plus

Stir Active Plus into clean, warm water in a plastic bucket: General Cleaning 30 g per 1 litre, Heavy Duty 60 g per 1 litre, Extreme up to 120 g per 1 litre. For better results use hot water (never boiling). Stir until it dissolves.

Apply generously: wallsWALLS
Apply generously: floorsFLOORS
4Treat

Apply generously

Work in sections you can keep wet. Walls: apply with a sponge or soft brush, starting at the bottom and working up, so run-off always lands on a wet surface. Floors: apply with a clean mop.

Allow 10–15 minutes dwell time: wallsWALLS
Allow 10–15 minutes dwell time: floorsFLOORS
5Treat

Allow 10–15 minutes dwell time

DON'T ALLOW THE PRODUCT TO DRY ON THE SURFACE: ADD MORE SOLUTION TO KEEP IT WET AND ACTIVE. Walls: solution runs off a wall, so go back over the section every few minutes.

Scrub: wallsWALLS
Scrub: floorsFLOORS
6Treat

Scrub

Scrub with a white (light), blue (moderate) or black (heavy) scrubbing pad, depending on severity. Rough or heavily textured surfaces: use a good quality stiff bristle brush to get in between the texture. Walls: or use the Scrub'N'Clean Kit - Walls. Floors: or use a Scrub'N'Clean Kit, Strip'N'Clean Kit or broom.

Pick up and rinse: wallsWALLS
Pick up and rinse: floorsFLOORS
7Remove + rinse

Pick up and rinse

Rinse thoroughly with clean water and keep the run-off away from plants and soil. Walls: rinse from the top of the wall down and pick up the run-off at the base with a wet vac or sponge. Floors: remove the dirty solution with a wet vac first, then rinse.

Check when dry, repeat if needed: wallsWALLS
Check when dry, repeat if needed: floorsFLOORS
8Remove + rinse

Check when dry, repeat if needed

Check the surface once it is fully dry and repeat as necessary until clean or the problem no longer moves. Stubborn, deep-set stain? Use the stain removal (paste) method.

Optional next step

Seal it for the look you want

Once the surface is clean and completely dry, seal it with either Aqua-Seal Gold+® or Enhance'N'Seal, depending on the final look you want. Sealing helps reduce future staining and makes cleaning easier.

Aqua-Seal Gold+: natural lookNATURAL LOOK
Aqua-Seal Gold+

For a natural look: Aqua-Seal Gold+®

Premium natural look sealer. The surface keeps its natural colour and finish, with premium stain protection against oil, food, grease and grime.

Enhance'N'Seal: colour enhanced lookCOLOUR ENHANCED LOOK
Enhance'N'Seal

For a colour enhanced look: Enhance'N'Seal

Premium sealer and colour enhancer. It enhances, darkens and highlights the colour of the surface as it seals. The colour change is permanent, so always do a test area first.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic, terrazzo and terracotta tiles, concrete, pavers and grout. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.

Mixing rates: Active Plus

Use Per 1 litre Per 4 litres
General Cleaning 30 g in warm/hot water 120 g in 4 L
Heavy Duty 60 g in warm/hot water 240 g in 4 L
Extreme up to 120 g in warm/hot water up to 480 g in 4 L

Use warm water. Hot water gives better results (never boiling). Mix only what you will use and dispose of any unused mixed solution after 4 hours.

Tips for the best result

  • Fix the source first: cap or seal weeping timber, redirect run-off from planters and garden beds, and trim back overhanging plants
  • Walls: bottom up to apply, top down to rinse
  • Work a section you can keep wet for the full dwell time. In warm weather, make the sections smaller
  • Use hot (not boiling) water for better results
  • Tannin or leaf stains on paving? See remove tannin stains and remove leaf stains
  • For deep-set, stubborn stains, use the stain removal (paste) method or see the Stain Removal Guide
  • Once clean and completely dry, seal porous surfaces with Aqua-Seal Gold+® for a natural look or Enhance'N'Seal for a colour enhanced look to help reduce future staining

Aftercare

Aqua-Seal Gold+

For a natural look: seal porous surfaces with Aqua-Seal Gold+® once the surface is clean and completely dry.

Enhance'N'Seal

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Always test first
  • Take care if using hot water to prevent scalding. Do not use boiling water
  • Wear skin, eye and foot protection
  • Use when the surface is between 4°C and 32°C
  • Keep away from plants, soil and metals
  • Once mixed, do NOT cover or store the mixed solution in a sealed container
  • Dispose of any unused solution after 4 hours by flushing with plenty of clean water into a toilet or drain
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

The degree of success depends on the surface stained, the type of stain, how long the stain has been in place and whether the surface was sealed or unsealed. Active Plus will not remove etch marks or restore polish to damaged areas. For deep-set, stubborn stains see Poultice Plus or Poultice Powder. Tannin stains can return while the source of the run-off remains.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp