HOW TO REMOVE PORCELAIN WAX FROM PORCELAIN TILES

Step-by-step instructions to help remove factory applied transit wax from new porcelain tiles, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Porcelain wax · No acids

Pre-wet, scrub, pick up, rinse

Many porcelain tiles leave the factory with a temporary transit wax. Left on after installation it can make tiles look dull and patchy and catch dirt. MicroScrub is a ready-to-use, non-acidic Nano Cream cleaner that helps remove most factory applied porcelain wax.

  • MicroScrub: ready to use, non-acidic Nano Cream. No dilution
  • Pour, scrub and rinse: no dwell time needed
  • Don't let the product dry on the surface
  • Pick up with a wet vac, then rinse thoroughly
  • Always test first, especially on polished and dark tiles
  • Heavy or stubborn wax: see Remove Porcelain Wax (Heavy) with XtremeClean+ + MicroScrub
MicroScrub
MICROSCRUB
250 ml · 1 L
$39.00 View product
XtremeClean+
XTREMECLEAN+ · HEAVY WAX
$51.00 View product

What is porcelain wax?

Porcelain wax is a coating applied at the factory during manufacture. It is intended to offer some protection while the tiles are boxed and in transit, as porcelain tiles stacked closely together can scratch each other.

If it isn't removed after installation it can leave tiles looking dull, patchy and dirty, and over time it can catch dirt, making the tiles look dirty and harder to clean.

LIGHT OR HEAVY? Start with MicroScrub. For heavy or stubborn wax, follow the heavy porcelain wax method with XtremeClean+ and MicroScrub.

Watch the video

MicroScrub - How To Use - Sealers Plus

MicroScrub - How To Use - Sealers Plus

Suitable for

  • New porcelain tiles, matt and textured (test first on polished)
  • Ceramic tiles with a factory wax coating
  • Floors and walls, indoors and outdoors

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

What you'll need

  • MicroScrub
  • Scrub'N'Clean Kit, white nylon pad or scrub brush (never a black or green pad on polished surfaces)
  • Grout brush for joints and edges
  • Spray bottle or pump sprayer with clean water
  • Broom, plus a wet vac (recommended) or mop
  • Plenty of clean water and cotton towels
  • Skin and eye protection
  • Optional: slow-speed scrub machine for larger areas

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C
  • Work out of direct sun and wind so the product doesn't dry
  • Take extra care on polished and dark coloured tiles and grout
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Prepare the area1Prepare

Prepare the area

Sweep, vacuum or wipe the surface to remove loose dirt and grit.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try MicroScrub on a small, hidden spot. Check colour stability, polished or dark surfaces and grout, and how well the wax lifts.

Lightly pre-wet3Prepare

Lightly pre-wet

Slightly pre-wet the surface and grout joints with clean water. On walls, spray water from a spray bottle.

Apply MicroScrub4Treat

Apply MicroScrub

Pour approx. 1–2 cups (250–500 mL) of MicroScrub onto the pre-wet surface. Use it as is: no dilution. On walls, apply it directly to a white nylon pad. Work in small sections.

Scrub straight away5Treat

Scrub straight away

Scrub with a white nylon pad, scrub brush or scrub machine. No dwell time needed. Don't allow the product to dry on the surface: add a little water to keep it wet and active.

Work the joints and edges6Treat

Work the joints and edges

Work the grout joints, edges and corners with a grout brush where residue builds up.

Pick up and rinse7Remove + rinse

Pick up and rinse

Remove the dirty solution with a wet vac or mop, then rinse thoroughly with clean water and pick up the rinse water too.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Wipe dry with cotton towels and check the area once fully dry, in good light. Repeat as necessary.

How much MicroScrub?

Use Dilution Amount
Floors Use as is (do not dilute) Approx. 1–2 cups (250–500 mL) per section, onto the pre-wet surface
Walls & vertical surfaces Use as is Apply directly to a white nylon pad after spraying the surface with water
As a booster Add to the standing solution Follow the cleaner or problem solver directions, then add MicroScrub just before scrubbing

Tips for the best result

  • Work in small sections and never let the product dry on the surface
  • Pick up all of the dirty solution: residue left behind can dry back on
  • Check the result once fully dry, in raking light
  • Remove the wax before sealing or grout sealing so products can bond properly
  • Wax still there? Follow the heavy porcelain wax method with XtremeClean+ + MicroScrub
  • For other stains, see the Stain Removal Guide

Aftercare

Aqua-Seal Gold+

Aqua-Seal Gold+®: if a porous surface (polished porous porcelain or grout) needs (re)sealing, apply once clean and fully dry, following the label.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

Aqua-Seal Gold+® is for porous surfaces only. Other porcelain finishes take a different sealer: use the Product Selector to find the right one for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Wear appropriate skin and eye protection
  • Use when the surface temperature is between 4°C and 32°C
  • Do not allow product to contact any non-recommended surfaces
  • Take care on dark coloured grout or stone, and on polished or glossy surfaces
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

MicroScrub removes surface sealers, finishes and residue only. It will not remove penetrating sealers or deep-set stains below the surface. Polished and dark surfaces may scratch or dull: test first.

Heavy or stubborn porcelain wax may need XtremeClean+ (see the heavy porcelain wax guide), Aqua-Strip or Strip-It.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp