HOW TO REMOVE LIGHT EPOXY GROUT HAZE
Step-by-step instructions for porcelain and ceramic tiles, natural stone and other suitable hard surfaces, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.
Start at 1:3, keep wet, scrub and rinse
Aqua-Strip is a Professional Grade, water dilutable cleaner and stripper that helps remove light epoxy grout haze left after installation. For light epoxy haze start at 1:3, up to neat depending on severity, with 10 – 60 minutes dwell and scrubbing. MicroScrub can be used as an optional booster just before scrubbing.
- Light epoxy haze: Aqua-Strip 1:3, up to neat depending on severity
- 10 – 60 minutes dwell; keep wet throughout
- White nylon pad, scrub brush or slow speed scrubber
- Wet vac or mop, then rinse thoroughly with clean water
- May affect polished surfaces: always test first
- Heavy, thick or cured haze: see Remove Heavy Epoxy Grout Haze
Light or heavy epoxy grout haze?
Epoxy grout haze is the thin resin film left on tile or stone faces after installation. It can look dull, sticky or smeary in side light. The grout maker's installation and initial-cleaning directions remain important.
MicroScrub helps remove light epoxy haze and can boost the standing Aqua-Strip solution just before scrubbing. As an abrasive cleaner it may scratch or dull polished and dark surfaces: test first.
Light epoxy grout haze on porcelain tiles

Suitable for
- Porcelain and ceramic tiles, terrazzo, mosaics and encaustic tiles
- Natural stone including marble, limestone, travertine, granite and slate: test first
- Concrete, bricks, pavers and terracotta
- Light epoxy grout haze left on suitable hard surfaces after installation
Where to use
- Domestic: homes, units, duplexes etc
- Commercial: hotels, shopping centres, restaurants, schools, aged care etc
Not for
- Any surface that fails the test area
- Polished surfaces without a successful test: Aqua-Strip at 1:2 or stronger may affect the finish
- Heavy, thick or cured haze: see Remove Heavy Epoxy Grout Haze
What you'll need
- Aqua-Strip; optional MicroScrub booster
- Chemical resistant gloves, protective clothing and eye / face protection
- Mop, brush or sponge for application; plastic bucket if needed
- White nylon pad, scrub brush or slow speed scrubber
- Wet vac or mop and plenty of clean water
Before you start
- Always do a test area first
- Surface temperature between 4°C and 32°C
- Read the grout maker's installation and cleaning directions
- Protect non-recommended surfaces and ventilate well
- Keep children and pets away; avoid contact during pregnancy or while nursing
Step-by-step
Prepare → Treat → Remove + rinse
1Prepare
Prepare and protect the area
Sweep, vacuum or wipe away loose dirt. Protect nearby non-recommended surfaces and ventilate well. Wear chemical resistant gloves, protective clothing and eye / face protection.
2Prepare
Do a test area first
VERY IMPORTANT
Test on a small, hidden spot to check colour stability, ease of application and the result when dry. Aqua-Strip at 1:2 or stronger may affect polished surfaces; MicroScrub may scratch or dull polished and dark surfaces.
3Treat
Apply Aqua-Strip: start at 1:3
Start with Aqua-Strip diluted 1:3 (1.3 L per 4 L of clean water) and carefully apply it to a small, manageable area using a mop, brush or sponge. Use it stronger, up to neat, depending on the severity of the haze.
4Treat
Dwell for 10 – 60 minutes
Allow 10 – 60 minutes dwell time. Do NOT allow product to dry on the surface: add more product as required to keep it wet and active.
5Treat
Scrub the wet haze
Scrub with a white nylon pad, scrub brush or slow speed scrubber for larger areas. Optional booster: following its TB, add MicroScrub to the standing solution just before scrubbing, then rinse thoroughly. Do not add other chemicals.
6Remove + rinse
Pick up the dirty solution
Remove the loosened haze and dirty solution with a wet vac or mop. Do not let the dirty solution dry back onto the tiles.
7Remove + rinse
Rinse thoroughly
Rinse thoroughly with plenty of clean water. Pick up the rinse water with a wet vac or mop and allow the surface to dry.
8Remove + rinse
Check dry and repeat if needed
Check the result when dry and repeat as necessary. Heavy, thick or cured haze may need Strip-It: see Remove Heavy Epoxy Grout Haze. Before any new sealer or coating, allow thorough drying and do a test area.
Dilution rates: Aqua-Strip
| Task | Ratio | Add to 4 L water | Makes |
|---|---|---|---|
| Light cleaning / degreasing | 1:10 | 400 mL | 4.4 L |
| Moderate cleaning / degreasing | 1:5 | 800 mL | 4.8 L |
| Heavy duty cleaning / degreasing | 1:2 | 2 L | 6 L |
| STRIPPING sealers & light epoxy grout haze | 1:3 | 1.3 L | 5.3 L |
| EXTREME: stripping sealers & epoxy haze | Neat | No water | Undiluted |
Light epoxy haze: start at 1:3, up to neat depending on severity. The other rows are general-cleaning rates. For diluted jobs, always add product to clean water to prevent splashing. Dwell 10 – 60 minutes and keep wet.
Tips for the best result
- Work in manageable areas so the product stays wet and active
- Use a white nylon pad or scrub brush, not an aggressive pad on polished surfaces
- Optional MicroScrub: add only to the standing solution just before scrubbing, following its TB
- Check the surface dry and in side light before deciding whether to repeat
- Heavy, thick or cured residue: see Remove Heavy Epoxy Grout Haze
Aftercare

For a natural look: seal porous surfaces with Aqua-Seal Gold+® once clean and completely dry, to help reduce staining and make cleaning easier.

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+: Daily / Weekly cleaning, pH neutral.
Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles, pavers and grout. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.
Precautions
- Read the entire label, SDS and technical bulletin before using
- DANGER: causes severe skin burns and eye damage. Wear chemical resistant gloves, protective clothing and eye / face protection
- Do NOT breathe fumes, mist, vapours or spray. Use only in a well ventilated area. Do NOT kneel in product
- Avoid contact during pregnancy or while nursing
- Use when the surface temperature is between 4°C and 32°C
- Do NOT allow contact with non-recommended surfaces. Aqua-Strip at 1:2 or neat may affect polished surfaces
- MicroScrub may scratch or dull polished and dark surfaces. Always test first
- Do NOT mix with other chemicals. Only use the optional MicroScrub booster as directed in its TB
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Limitations
This guide is for light epoxy haze. Results depend on the surface, film thickness and how far the residue has cured. Repeat treatment may be needed. Heavy, thick or cured haze may require Strip-It: see Remove Heavy Epoxy Grout Haze. Aqua-Strip at 1:2 or stronger may affect polished finishes; MicroScrub may scratch or dull polished and dark surfaces. Allow the surface to dry thoroughly and test before applying any new sealer or coating. Seal only porous surfaces after successful cleaning and thorough drying.
For other stains and problems, see our Problem Solvers and the Stain Removal Guide.
For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.
Important note
These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.


