HOW TO REMOVE BIRD DROPPINGS FROM NATURAL STONE, PAVERS & CONCRETE

Step-by-step instructions for outdoor natural stone, ceramic, porcelain, encaustic and terrazzo tiles, concrete, grout, pavers and bricks, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Bird & animal droppings

Lift off, mix, dwell, scrub, rinse

Active Plus is an easy to use, 100% actives, super concentrated, triple action cleaner, deodoriser and stain remover. It is non-acidic, so it is suitable for acid-sensitive stone such as marble, limestone and travertine, plus concrete, pavers, etc. Mixed with warm water, it helps remove bird and animal dropping stains, along with the odours they leave behind.

  • Lift off the droppings first. Don't dry sweep or pressure wash them
  • Powder: General Cleaning 30 g, Heavy Duty 60 g or Extreme up to 120 g per 1 litre of warm water
  • Allow 10–15 minutes dwell time. Don't let it dry on the surface. Add more product to keep it wet and active
  • Scrub, pick up with a wet vac, then rinse thoroughly
  • Non-acidic: safe on natural stone incl. marble, limestone & travertine. Always test first
  • Stubborn, deep-set marks: use the paste method
  • Treat droppings early: they can etch acid-sensitive stone and other surfaces
Active Plus 2 kg
ACTIVE PLUS
300 g · 1 kg · 2 kg
$72.00 View product

Why do bird droppings stain and mark stone?

Bird droppings contain uric acid, natural dyes from the berries and fruit birds eat, and organic matter. On porous surfaces such as natural stone, concrete, pavers and grout, the colour soaks in and leaves white, purple, brown or dark marks, especially under trees, eaves, power lines and pool fences.

The acid in fresh droppings can also etch calcium-based stone such as marble, limestone and travertine, plus pavers, concrete, etc., leaving a dull or rough spot. The longer droppings sit, the deeper the stain and the greater the risk of etching, so lift them off and treat the mark early. How well it lifts depends on the surface, how long the mark has been there and whether the surface was sealed.

TIP: once the stain is removed and the surface is completely dry, seal porous surfaces with Aqua-Seal Gold+® for a natural look or Enhance'N'Seal for a colour enhanced look, to help reduce future staining and make cleaning easier.

Bird droppings on travertine pavers

Bird droppings on travertine pavers

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Etch marks or dull, damaged polish: it won't remove etching or restore polish

What you'll need

  • Active Plus
  • Scrub'N'Clean Kit, a white (light), blue (moderate) or black (heavy) scrubbing pad depending on severity; rough or heavily textured surfaces: a good quality stiff bristle brush
  • Strip'N'Clean Kit for heavy duty scrubbing
  • Paper towels, a plastic scraper and a bin bag to lift off the droppings
  • Plastic bucket and warm/hot water (not boiling)
  • Kitchen scales or a measuring cup
  • Wet vac (recommended) to pick up the dirty solution
  • Plenty of clean water for rinsing
  • Gloves, eye, skin and foot protection
  • Paste method: plastic wrap, residue-free tape, plastic spatula, paper towels

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C
  • Wear gloves and eye protection: droppings can carry germs. Wash your hands afterwards
  • Keep the solution away from plants, soil and metals
  • Mix only what you'll use: never cover or store the mixed solution in a sealed container
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Lift off the droppings1Prepare

Lift off the droppings

Mist dried droppings with clean water to soften them, then lift them off with paper towels and a plastic scraper and put them in the bin. Don't dry sweep or pressure wash dried droppings: it spreads them and raises dust. Then pre-wet the surface with clean water.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try the solution on a small, hidden spot to check surface colour stability and how well the stain lifts.

Mix Active Plus3Treat

Mix Active Plus

Stir Active Plus into clean, warm water in a plastic bucket: General Cleaning 30 g, Heavy Duty 60 g or Extreme up to 120 g per 1 litre, e.g. 120 g, 240 g or up to 480 g in 4 litres. For better results use hot water (never boiling). Stir until it dissolves.

Apply generously4Treat

Apply generously

Apply the solution generously over the marks with a clean mop, or pour it over them from a plastic watering can. Clean large areas in sections. On walls / vertical surfaces, apply from the bottom up and rinse from the top down.

Allow 10–15 minutes dwell time5Treat

Allow 10–15 minutes dwell time

Allow to dwell for 10–15 minutes. Don't allow the product to dry on the surface: add more product to keep it wet and active.

Scrub6Treat

Scrub

Scrub with a Scrub'N'Clean Kit and a white (light), blue (moderate) or black (heavy) scrubbing pad depending on severity. Rough or heavily textured surfaces: use a good quality stiff bristle brush to get in between the texture.

Pick up and rinse7Remove + rinse

Pick up and rinse

Remove the dirty solution with a wet vac, then rinse thoroughly with clean water.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the area once it is fully dry and repeat as necessary. Stubborn, deep-set mark? Use the paste method below.

Mixing rates: Active Plus

Use Per 1 litre Per 4 litres
General Cleaning 30 g in warm/hot water 120 g in 4 L
Heavy Duty 60 g in warm/hot water 240 g in 4 L
Extreme up to 120 g in warm/hot water up to 480 g in 4 L

Dispose of any unused mixed solution after 4 hours.

Stubborn marks: paste method

  1. Mix Active Plus with warm water to a thick toothpaste / peanut butter consistency
  2. Apply a finger-thick, even coat over the mark, covering slightly more than the mark
  3. Optional on floors: cover with plastic wrap, tape down the edges with residue-free tape and poke a few holes in the wrap
  4. Leave until the paste dries (24–48 hours depending on conditions), or for at least 24 hours
  5. Lift off with a plastic spatula, mist with clean water and scrub lightly with a white (light), blue (moderate) or black (heavy) scrubbing pad depending on severity, or a brush
  6. Rinse thoroughly with clean water, dry with paper towels and repeat as necessary

Tips for the best result

  • Treat droppings early: the longer they sit, the deeper the stain and the higher the risk of etching
  • Fix the source: trim branches over paving and pools, and use bird deterrents on eaves, beams and fences
  • Use hot (not boiling) water for better results
  • Work in sections you can keep wet, and never let the solution dry on the surface
  • Still marked after the paste method? Keep repeating the process until it all comes off or stops moving. For deep stains use Active Plus following the Stain Removal Instructions
  • Once clean and completely dry, seal porous surfaces with Aqua-Seal Gold+® for a natural look or Enhance'N'Seal for a colour enhanced look to help reduce future staining

Aftercare

Aqua-Seal Gold+

For a natural look: re-seal porous surfaces with Aqua-Seal Gold+® once the stain is removed and the surface is completely dry.

Enhance'N'Seal

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles, concrete, pavers and grout. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Always test first
  • Take care if using hot water to prevent scalding. Do not use boiling water
  • Wear gloves, skin, eye and foot protection
  • Use when the surface is between 4°C and 32°C
  • Keep away from plants, soil and metals
  • Once mixed, do NOT cover or store the mixed solution in a sealed container
  • Dispose of any unused solution after 4 hours by flushing with plenty of clean water into a toilet or drain
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

The degree of success depends on the surface stained, the type of stain, how long the stain has been in place and whether the surface was sealed or unsealed. Active Plus will not remove etch marks or restore polish to damaged areas: etched stone may need professional honing or polishing.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp