HOW TO REMOVE EFFLORESCENCE FROM WALLS

Step-by-step instructions for ceramic and porcelain wall tiles, brick walls, splashbacks, retaining and feature walls of acid-resistant material, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Efflorescence · Walls

Apply neat, dwell, scrub, rinse

Oxi Gel+ is a Professional Grade, ready-to-use, high viscosity acid cling gel cleaner and hard surface disinfectant. It clings to walls, so it stays where you put it, and helps remove efflorescence from acid-resistant vertical surfaces.

  • Ready to use: no dilution, apply neat
  • Clings to walls, splashbacks, showers and other vertical surfaces
  • Minimum 10 minutes dwell time. Don't let it dry on the surface
  • Scrub with the Scrub'N'Clean Kit - Walls, rinse thoroughly, wipe dry
  • For acid-resistant surfaces only. Always test first
  • Protect the floor, drain, tapware and fixtures
  • Floors? See Remove Efflorescence from Tiles, Bricks & Pavers
Oxi Gel+ 1 litre
OXI GEL+ · WALLS
1 L · 4 L
$72.00 View product

What is efflorescence?

Efflorescence is the white, powdery or crusty salt deposit that can appear on wall tiles, grout, bricks and mortar. Water moving through cement-based materials such as grout, adhesive, render and mortar dissolves natural salts and carries them to the surface. When the water evaporates, the salts are left behind.

It often shows up on new installations and brickwork while they cure and dry out, and it can return while moisture keeps moving through the wall. Plain water alone often just re-dissolves the salts, which can reappear as the surface dries.

THE EFF-CONTROL+ SYSTEM: prevent with Eff-Shield+ in the grout, adhesive and mortar of new installations, and remove with Oxi Gel+ (walls) or OxiTreat+ (floors).

Efflorescence on a brick feature wall

Efflorescence on a brick feature wall

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

What you'll need

  • Oxi Gel+
  • Scrub'N'Clean Kit - Walls, white nylon pad or scrub brush
  • Sponge to apply and rinse
  • Grout brush for the joints
  • Plastic sheet and tape to protect the floor, drain and fixtures
  • Plastic bucket (never metal), plenty of clean water
  • Cotton towels to wipe dry, wet vac (optional)
  • Acid-resistant gloves, eye protection and protective clothing

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C. Not in direct hot sun
  • Protect the floor, drain, tapware, chrome and any acid-sensitive surfaces
  • Ventilate the area well
  • Never mix with other chemicals, especially chlorine bleach
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Prepare and protect1Prepare

Prepare and protect

Wipe the wall to remove loose dust and debris. Cover the floor, drain, tapware and fixtures with plastic sheet and tape, and protect any acid-sensitive surfaces nearby.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try Oxi Gel+ on a small, hidden spot. Check colour stability, dark grouts and grout colourants, and how well the efflorescence lifts.

Apply Oxi Gel+ neat3Treat

Apply Oxi Gel+ neat

Ready to use, no dilution. Pour onto a gloved hand, sponge or white nylon pad and smear evenly over the area. Work in sections you can keep wet.

Allow 10 minutes dwell time4Treat

Allow 10 minutes dwell time

The gel clings to vertical surfaces. Allow a minimum dwell time of 10 minutes. Don't allow the product to dry on the surface: add more to keep it wet and active.

Scrub5Treat

Scrub

Scrub with the Scrub'N'Clean Kit - Walls, a white nylon pad or scrub brush.

Scrub the joints6Treat

Scrub the joints

Work the grout joints with a grout brush.

Remove and rinse7Remove + rinse

Remove and rinse

Remove the dirty gel with a sponge, cloths or wet vac. Rinse thoroughly with clean water using a sponge or spray, then wipe dry with cotton towels.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the wall once it is fully dry. Repeat the process as necessary until you're happy with the result.

Technical data: Oxi Gel+

Item Detail
Dilution None: ready to use, apply neat
Dwell time Minimum 10 minutes, keep wet
Application Surface temperature 4°C – 32°C, not in direct hot sun
Product type Acid cling gel cleaner and hard surface disinfectant, pH <3
Pack sizes 1 L · 4 L

Cleaning a floor? Use OxiTreat+, the concentrated version: see Remove Efflorescence from Tiles, Bricks & Pavers.

Tips for the best result

  • Dry-brush loose salts off the wall first
  • If efflorescence keeps coming back, have the wall checked for where the moisture is coming from (flashings, drainage, waterproofing)
  • Work in small sections and never let the gel dry on the surface
  • Work from the bottom up and rinse from the top down to help avoid streaks
  • On dark grouts and grout colourants, check the test area once fully dry
  • Acid-sensitive walls (marble, limestone, travertine)? Never use acids: see the acid-sensitive surfaces guide or call us

Aftercare

Condense Plus 1 litre

Condense Plus: 1. External walls (brick, concrete, natural stone). Once the efflorescence is gone and the wall is fully dry, apply 1 coat to help consolidate and strengthen the surface. It greatly increases water repellency, so less water soaks in to carry salts out, helping reduce efflorescence coming back. 24 hour cure. Not for glazed or non-porous tiles.

Aqua-Seal Gold+

2. Stain protection, natural look. Once clean and completely dry (external walls: after Condense Plus has cured), seal grout and other porous surfaces with Aqua-Seal Gold+® to help reduce staining.

Enhance'N'Seal

Or, for a colour enhanced look: seal grout and other porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning and disinfecting.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: grout, natural stone and concrete. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Wear acid-resistant gloves, protective clothing and eye/face protection
  • Avoid breathing fumes, mist or vapours. Use in a well ventilated area
  • Use when the surface temperature is between 4°C and 32°C
  • Do NOT allow contact with acid-sensitive surfaces, metals, chrome or tapware
  • Do NOT mix with other chemicals (especially chlorine bleach)
  • May affect dark grouts, grout colourants and polished surfaces. Do NOT use on polished natural stone
  • Hard surface disinfectant only. Do NOT use on skin
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

Oxi Gel+ is for acid-resistant surfaces only. It will etch marble, limestone, travertine, terrazzo and other acid-sensitive surfaces: use Stone Gel+, Haze Away or MicroScrub instead. Efflorescence is driven by moisture, so it can return until the moisture source is fixed. Badly stained grout may require re-grouting or re-colouring with Colour'N'Seal.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp