HOW TO REMOVE PENCIL, RUST & METAL MARKS FROM WALL TILES
Step-by-step instructions for ceramic, porcelain and tessellated wall tiles, splashbacks and shower walls, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.
Apply neat, dwell, scrub, rinse
Oxi Gel+ is a Professional Grade, ready-to-use, high viscosity acid cling gel cleaner and hard surface disinfectant. It clings to walls, so it stays where you put it, and helps remove pencil, rust and metal marks from acid-resistant vertical surfaces.
- Ready to use: no dilution, apply neat
- Clings to walls, splashbacks, showers and other vertical surfaces
- Minimum 10 minutes dwell time. Don't let it dry on the surface
- Scrub with the Scrub'N'Clean Kit - Walls, rinse thoroughly, wipe dry
- For acid-resistant surfaces only. Always test first
- Protect the floor, drain, tapware and fixtures
- Floors? See Remove Pencil, Rust or Metal from Tiles
Where do these marks come from?
Pencil lines from setting out during installation, grey metal marks from tools, trims, ladders and appliances, and orange rust streaks from fixings, shelving or bore water can all mark wall tiles.
On matte and textured tiles these marks can sit in the surface texture and resist everyday cleaning. An acid cleaner helps dissolve the metal and rust residue so it can be scrubbed and rinsed away.
Pencil, metal and rust marks on wall tiles

Suitable for
- Wall tiles, splashbacks, laundry and shower walls
- Ceramic, porcelain, tessellated and quarry tiles
- Bricks, pavers, mosaics, terracotta, shower glass and engineered stone
- Acid-resistant natural stone e.g. granite, quartz, bluestone, basalt, slate, sandstone (test first)
Where to use
- Domestic: homes, units, duplexes etc
- Commercial: hotels, shopping centres, restaurants, schools, aged care etc
Not for
- Marble, limestone, travertine, terrazzo, encaustic tiles, concrete or polished natural stone: use MicroScrub on polished natural stone and acid-sensitive surfaces
- Metals, chrome and tapware (protect them)
- Floors: see Remove Pencil, Rust or Metal from Tiles
What you'll need
- Oxi Gel+
- Scrub'N'Clean Kit - Walls, white nylon pad or scrub brush
- Sponge to apply and rinse
- Grout brush for the joints
- Plastic sheet and tape to protect the floor, drain and fixtures
- Plastic bucket (never metal), plenty of clean water
- Cotton towels to wipe dry, wet vac (optional)
- Acid-resistant gloves, eye protection and protective clothing
Before you start
- Always do a test area first
- Surface temperature between 4°C and 32°C. Not in direct hot sun
- Protect the floor, drain, tapware, chrome and any acid-sensitive surfaces
- Ventilate the area well
- Never mix with other chemicals, especially chlorine bleach
- Keep children and pets away until the area is rinsed and dry
Step-by-step
Prepare → Treat → Remove + rinse
1Prepare
Prepare and protect
Wipe the wall to remove loose dust and debris. Cover the floor, drain, tapware and fixtures with plastic sheet and tape, and protect any acid-sensitive surfaces nearby.
2Prepare
Do a test area first
VERY IMPORTANT
Try Oxi Gel+ on a small, hidden spot. Check colour stability, dark grouts and grout colourants, and how well the pencil, rust and metal marks lifts.
3Treat
Apply Oxi Gel+ neat
Ready to use, no dilution. Pour onto a gloved hand, sponge or white nylon pad and smear evenly over the area. Work in sections you can keep wet.
4Treat
Allow 10 minutes dwell time
The gel clings to vertical surfaces. Allow a minimum dwell time of 10 minutes. Don't allow the product to dry on the surface: add more to keep it wet and active.
5Treat
Scrub
Scrub with the Scrub'N'Clean Kit - Walls, a white nylon pad or scrub brush.
6Treat
Scrub the joints
Work the grout joints with a grout brush.
7Remove + rinse
Remove and rinse
Remove the dirty gel with a sponge, cloths or wet vac. Rinse thoroughly with clean water using a sponge or spray, then wipe dry with cotton towels.
8Remove + rinse
Check when dry, repeat if needed
Check the wall once it is fully dry. Repeat the process as necessary until you're happy with the result.
Technical data: Oxi Gel+
| Item | Detail |
|---|---|
| Dilution | None: ready to use, apply neat |
| Dwell time | Minimum 10 minutes, keep wet |
| Application | Surface temperature 4°C – 32°C, not in direct hot sun |
| Product type | Acid cling gel cleaner and hard surface disinfectant, pH <3 |
| Pack sizes | 1 L · 4 L |
Cleaning a floor? Use OxiTreat+, the concentrated version: see Remove Pencil, Rust or Metal from Tiles.
Tips for the best result
- Remove the cause of rust marks (rusty fixings, shelving, bore water) first
- Protect nearby metal fixtures: acid can mark them
- Work in small sections and never let the gel dry on the surface
- Work from the bottom up and rinse from the top down to help avoid streaks
- On dark grouts and grout colourants, check the test area once fully dry
- Acid-sensitive walls (marble, limestone, travertine)? Never use acids: see the acid-sensitive surfaces guide or call us
Aftercare

For a natural look: seal grout and other porous surfaces with Aqua-Seal Gold+® once clean and completely dry, to help reduce staining.

For a colour enhanced look: seal grout and other porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+: Daily / Weekly cleaning and disinfecting.

XtremeClean+: Half yearly or as needed heavy-duty clean.
Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: grout and tessellated tiles. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.
Precautions
- Read the entire label, SDS and technical bulletin before using
- Wear acid-resistant gloves, protective clothing and eye/face protection
- Avoid breathing fumes, mist or vapours. Use in a well ventilated area
- Use when the surface temperature is between 4°C and 32°C
- Do NOT allow contact with acid-sensitive surfaces, metals, chrome or tapware
- Do NOT mix with other chemicals (especially chlorine bleach)
- May affect dark grouts, grout colourants and polished surfaces. Do NOT use on polished natural stone
- Hard surface disinfectant only. Do NOT use on skin
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Limitations
Oxi Gel+ is for acid-resistant surfaces only. It will etch marble, limestone, travertine, terrazzo and other acid-sensitive surfaces: use Stone Gel+, Haze Away or MicroScrub instead. Deep-set rust stains may need several applications. Badly stained grout may require re-grouting or re-colouring with Colour'N'Seal.
For other stains and problems, see our Problem Solvers and the Stain Removal Guide.
For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.
Important note
These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.

