HOW TO REMOVE LATEX-MODIFIED GROUT HAZE FROM PORCELAIN TILES
Step-by-step instructions for porcelain and ceramic tiles grouted with a grout booster or latex additive, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.
Cement first, then the latex film
Grout mixed with a liquid grout booster or latex additive leaves a two-layer haze if it dries on the tile face: cement residue plus a thin polymer (latex) film. OxiTreat+ helps remove the cement. Aqua-Strip helps remove the latex film the acid leaves behind, with Strip-It for heavy film.
- Under 10 days: Haze Away at 1:4 (very light), 1:2 (light), 1:1 or neat (heavier)
- Cement haze: OxiTreat+ at 1:2 (floors) or Oxi Gel+ neat (walls)
- Latex film left after the acid: Aqua-Strip at 1:5 or 1:2
- Heavy film: Strip-It neat, then XtremeClean+ at 1:5
- Never mix products. Rinse thoroughly between steps
- For acid-resistant tiles only. Always test first
- Keep away from non-recommended surfaces
Why is this haze so hard to remove?
Grout boosters and latex additives make cement grout stronger, more flexible and more stain resistant. As the grout cures, the polymer also forms a thin film over and through any cement residue left on the tiles.
An acid cleaner dissolves the cement but not the polymer, so after an acid clean the tiles can still look dull, cloudy or smeary, especially when wet or in side light. That leftover film needs an alkaline stripper, not more acid.
Latex grout haze on porcelain tiles

Suitable for
- Ceramic, porcelain and tessellated tiles
- Terracotta, quarry tiles and mosaics
- Acid-resistant pavers and engineered stone
- Acid-resistant natural stone e.g. granite, bluestone, basalt, slate (test first)
Where to use
- Domestic: homes, units, duplexes etc
- Commercial: hotels, shopping centres, restaurants, schools, aged care etc
Not for
- Marble, limestone, travertine, terrazzo, concrete or other acid-sensitive surfaces
- Polished surfaces, metals, chrome or glass fittings (protect them)
- Polished natural stone and acid-sensitive surfaces: see Remove Grout Haze from Natural Stone
What you'll need
- OxiTreat+ (floors) or Oxi Gel+ (walls), Aqua-Strip, Strip-It (heavy film)
- Scrub'N'Clean Kit, plus white, blue and black scrubbing pads (light, moderate, heavy)
- Good quality stiff bristle brush for rough or textured tiles, and a grout brush for the joints
- Plastic buckets and measuring jug (never metal)
- Wet vac (recommended) or mop, roller for Strip-It
- Plenty of clean water and cotton towels
- Chemical resistant gloves, eye protection and a suitable mask
- Optional: slow-speed scrub machine for larger areas
Before you start
- Always do a test area first
- Surface temperature between 4°C and 32°C
- Work out of direct hot sun and wind so products don't dry
- Protect metal, chrome and glass fittings, floor wastes and acid-sensitive surfaces nearby
- Ventilate the area well (essential with Strip-It)
- Keep children, pets and anyone pregnant or nursing away until the area is rinsed and dry
Step-by-step
Prepare → Treat → Finish
1Prepare
Prepare the area
Sweep or vacuum the floor. Protect metal, chrome and glass fittings, floor wastes, plants and any acid-sensitive surfaces nearby, and ventilate the area well.
2Prepare
3Treat
4Treat
Dwell, scrub, pick up, rinse
Allow a minimum of 10 minutes. Don't allow the product to dry on the surface: add more to keep it wet and active. Scrub with a white (light), blue (moderate) or black (heavy) scrubbing pad, depending on how heavy the haze is. On rough or heavily textured tiles, use a good quality stiff bristle brush to get in between the texture. Pick up with a wet vac and rinse thoroughly with clean water.
5Treat
Check it dry, against the light
Once dry, look across the floor towards a window. A dull, patchy or smeary film that is still there is the latex (polymer) film from the grout additive: acid won't remove it.
6Treat
Remove the latex film: Aqua-Strip
Apply Aqua-Strip at 1:5 (1:2 for heavier film). Allow 10 – 60 minutes and keep it wet. Scrub with a white (light), blue (moderate) or black (heavy) scrubbing pad, depending on how heavy the haze is. On rough or heavily textured tiles, use a good quality stiff bristle brush to get in between the texture. Pick up with a wet vac and rinse thoroughly.
7Treat
Heavy film only: Strip-It
If the film still won't shift, apply Strip-It neat to a manageable area. Allow 30 minutes – 2 hours and keep it wet. Scrub with a black pad (stiff bristle brush on textured tiles), wet vac and rinse, then scrub again with XtremeClean+ at 1:5 and rinse.
8Finish
Dry and seal the grout
Check the floor once fully dry and repeat any step as needed. Allow at least 48 hours after Strip-It, then seal the grout with Aqua-Seal Gold+®.
Which product, which dilution
| What you see | Product | Dilution (per 4 litres of water) | Dwell |
|---|---|---|---|
| Grout haze under 10 days old | Haze Away | 1:4 very light, 1:2 light, 1:1 or neat heavier | Minimum 10 min |
| Heavy or older cement haze: floors | OxiTreat+ | 1:2 (add 2 L, makes 6 L) | Minimum 10 min, keep wet |
| Heavy or older cement haze: walls | Oxi Gel+ | Ready to use: neat | Minimum 10 min, keep wet |
| Dull, smeary latex film left after the acid | Aqua-Strip | 1:5 (add 800 mL); 1:2 for heavier film | 10 – 60 min, keep wet |
| Heavy latex film Aqua-Strip won't shift | Strip-It | Ready to use: do NOT dilute | 30 min – 2 hours, keep wet |
| Residue after Strip-It | XtremeClean+ | 1:5 | Scrub, then rinse |
Always add product to clean water to prevent splashing. Never mix products: OxiTreat+ and Oxi Gel+ are acids, Aqua-Strip is strongly alkaline. Rinse thoroughly with clean water between steps.
Tips for the best result
- Treat grout haze as early as possible: the longer it stays, the harder it is to remove
- Pre-wet the grout joints before any acid so it works on the tile face, not in the grout
- Work in small sections and never let any product dry on the surface
- Match the pad to the problem: white for light haze, blue for moderate, black for heavy. Rough or textured tiles: a stiff bristle brush gets into the texture
- Check the floor dry and in side light between steps: that tells you whether the cement or the latex film is left
- Next time: clean all grout off the tile face before it dries, and add 1 L of Haze Away to 4 L of water (1:4) for the final grout wash
- Walls, splashbacks and showers: use Oxi Gel+ for the cement haze. See Remove Heavy Grout Haze from Wall Tiles
Aftercare

For a natural look: seal the clean, dry grout with Aqua-Seal Gold+® (at least 48 hours after Strip-It).

For a colour enhanced look: seal the grout with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+: Daily / Weekly cleaning, pH neutral.

XtremeClean+: Half yearly or as needed heavy-duty clean.
Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: here, the grout. Porcelain and ceramic tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.
Precautions
- Read the entire label, SDS and technical bulletin of each product before using
- Wear chemical resistant gloves, protective clothing and eye/face protection. Wear a suitable mask with Strip-It
- Do NOT breathe fumes, mist, vapours or spray. Use in a well ventilated area. Do not kneel in product
- Do NOT mix products or use them with other chemicals (especially chlorine bleach). Rinse thoroughly between steps
- Do NOT allow acids to contact acid-sensitive surfaces, metals, chrome or glass fittings. Never use metal buckets
- May affect dark grouts, grout colourants and polished surfaces
- Avoid contact during pregnancy or while nursing
- The floor will get slippery during the process. Take care to prevent slips and falls
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Limitations
For acid-resistant tiles only. Do not use OxiTreat+ or Oxi Gel+ on marble, limestone, travertine, terrazzo or other acid-sensitive surfaces. Epoxy grout haze is different: see Remove Heavy Epoxy Grout Haze. Badly stained grout may require re-grouting or re-colouring with Colour'N'Seal.
For other problems, see our Grout Haze Removal guide, Problem Solvers and the Stain Removal Guide.
For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.
Important note
These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.



