HOW TO REMOVE ALGAE, MOULD & MILDEW FROM STONE, TILES & PAVERS

Step-by-step instructions for natural stone, ceramic, porcelain, encaustic and terrazzo tiles, grout, concrete, pavers and other surfaces, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Algae, mould & mildew

Mix, dwell, scrub, rinse

Active Plus is an easy to use, 100% actives, super concentrated, triple action oxygen cleaner, deodoriser and stain remover. Mixed with warm water, it helps remove algae, mould, mildew, leaf and tannin stains, dirt and grime. It is non-acidic, so it is suitable for acid-sensitive surfaces.

  • Floors & paving: Active Plus, General Cleaning 30 g, Heavy Duty 60 g or Extreme up to 120 g per 1 litre of warm water
  • Walls & showers: Stone Gel+, ready-to-use cling gel: see remove mould from walls
  • Allow 10–15 minutes dwell time. Don't let it dry on the surface
  • Scrub, pick up with a wet vac, then rinse thoroughly
  • Safe on natural stone, ceramic & porcelain tile, grout & concrete. Always test first
  • Keep away from plants, soil and metals
Active Plus 2 kg
ACTIVE PLUS
300 g · 1 kg · 2 kg
$72.00 View product

What causes algae, mould and mildew?

Algae, mould and mildew grow where surfaces stay damp, shaded and poorly ventilated: south-facing paths and courtyards, pool surrounds, under trees, around downpipes and in bathrooms. Porous surfaces such as natural stone, concrete, pavers and grout hold moisture and give spores a place to take hold, leaving green, black or grey patches that can also become slippery.

Cleaning helps remove the growth and staining, but it can return while the conditions stay damp. Improving drainage, sunlight and airflow helps reduce regrowth.

TIP: once clean and completely dry, seal porous surfaces with Aqua-Seal Gold+® for a natural look or Enhance'N'Seal for a colour enhanced look, to help reduce water absorption and make cleaning easier.

Algae and mould on outdoor pavers

Algae and mould on outdoor pavers

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Plants, soil and metals (keep it away)
  • Etch marks or dull, damaged polish: it won't remove etching or restore polish

What you'll need

  • Active Plus
  • Scrub'N'Clean Kit, white (light), blue (moderate) or black (heavy) scrubbing pad depending on severity, or a scrub machine; rough or heavily textured surfaces: a good quality stiff bristle brush
  • Plastic bucket and warm/hot water (not boiling)
  • Kitchen scales or a measuring cup
  • Wet vac (recommended) to pick up the dirty solution
  • Bucket plus plenty of clean water for rinsing
  • Gloves, eye, skin and foot protection
  • Paste method: plastic wrap, residue-free tape, plastic spatula, paper towels

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C
  • Sweep away leaves, moss clumps and debris
  • Keep the solution away from plants, soil and metals
  • Mix only what you'll use: never cover or store mixed solution
  • Mix only what you'll use: never cover or store the mixed solution in a sealed container
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Sweep and pre-wet1Prepare

Sweep and pre-wet

Sweep away leaves and debris, then pre-wet the surface with clean water. On walls, pre-wet the wall and the ground below it, so run-off doesn't soak in and leave streaks.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try the solution on a small, hidden spot to check surface colour stability and results.

Mix Active Plus3Treat

Mix Active Plus

Stir Active Plus into clean, warm water in a plastic bucket: General Cleaning 30 g, Heavy Duty 60 g or Extreme up to 120 g per 1 litre, e.g. 120 g, 240 g or up to 480 g in 4 litres. For better results use hot water (never boiling). Stir until it dissolves.

Apply generously4Treat

Apply generously

Apply the solution generously to the surface with a clean mop or watering can. Clean large areas in sections. On walls / vertical surfaces, apply from the bottom up and rinse from the top down.

Allow 10–15 minutes dwell time5Treat

Allow 10–15 minutes dwell time

Allow to dwell for 10–15 minutes. Don't allow the product to dry on the surface: add more solution to keep it wet and active.

Scrub6Treat

Scrub

Scrub with a Scrub'N'Clean Kit and a white (light), blue (moderate) or black (heavy) scrubbing pad depending on severity, or a scrub machine. Rough or heavily textured surfaces: use a good quality stiff bristle brush to get in between the texture. Pay attention to grout joints and corners.

Pick up and rinse7Remove + rinse

Pick up and rinse

Remove the dirty solution with a wet vac, then rinse thoroughly with clean water.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the area once it is fully dry and repeat as necessary. Stubborn staining? Use the paste method below.

Mixing rates: Active Plus

Use Per 1 litre Per 4 litres
General Cleaning 30 g in warm/hot water 120 g in 4 L
Heavy Duty 60 g in warm/hot water 240 g in 4 L
Extreme up to 120 g in warm/hot water up to 480 g in 4 L

Dispose of any unused mixed solution after 4 hours.

Stubborn stains: paste method

  1. Mix Active Plus with warm water to a thick toothpaste / peanut butter consistency
  2. Apply a finger-thick, even coat over the stain, covering slightly more than the stain
  3. On walls: cover with plastic wrap and tape down all the edges with residue-free tape so the paste stays in place, then poke a few holes in the wrap. This step is required on walls; on floors, plastic wrap is optional
  4. Leave until the paste dries (24–48 hours depending on conditions), or for at least 24 hours
  5. Lift off with a plastic spatula, mist with clean water and scrub lightly with a white (light), blue (moderate) or black (heavy) scrubbing pad depending on severity, or a brush
  6. Rinse thoroughly with clean water, dry with paper towels and repeat as necessary

Tips for the best result

  • Treat growth early, before it spreads and stains
  • Improve drainage, sunlight and airflow where you can, and trim back overhanging plants
  • Use hot (not boiling) water for better results
  • Work in sections you can keep wet, and never let the solution dry on the surface
  • Shower walls, splashbacks or feature walls? See remove mould & mildew from walls with Stone Gel+
  • Regular cleaning with a pH neutral cleaner helps reduce regrowth

Aftercare

Aqua-Seal Gold+

For a natural look: seal porous surfaces with Aqua-Seal Gold+® once clean and completely dry, to help reduce water absorption.

Enhance'N'Seal

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles, concrete, pavers and grout. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Always test first
  • Take care if using hot water to prevent scalding. Do not use boiling water
  • Wear skin, eye and foot protection
  • Use when the surface is between 4°C and 32°C
  • Keep away from plants, soil and metals
  • Once mixed, do NOT cover or store the mixed solution in a sealed container
  • Dispose of any unused solution after 4 hours by flushing with plenty of clean water into a toilet or drain
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

The degree of success depends on the surface stained, the type of stain, how long the stain has been in place and whether the surface was sealed or unsealed. Active Plus will not remove etch marks or restore polish to damaged areas. Tannin stains can return while the source of the run-off remains. For deep-set, stubborn stains see Poultice Plus or Poultice Powder. Growth can return while the area stays damp and shaded.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp