HOW TO REMOVE MOULD & MILDEW FROM SHOWER, BATHROOM & FEATURE WALLS

Step-by-step instructions for natural stone, porcelain, ceramic, encaustic and terrazzo tiles and grout on shower walls, splashbacks, bathroom and laundry walls and outdoor feature walls, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Mould on walls

Apply, dwell, scrub, rinse

Stone Gel+ is a Professional Grade, ready-to-use, high viscosity alkaline cling gel cleaner, conditioner and commercial grade disinfectant. It clings to walls to help remove mould, soap scum, dirt and grime, and helps inhibit mould growth. Safe on all natural stone, porcelain, ceramic, encaustic, terrazzo and grout (always test first).

  • Ready to use: no mixing, apply neat
  • Clings to vertical surfaces: shower walls, splashbacks, feature walls
  • Minimum 10 minutes dwell time. Don't let it dry on the surface
  • Scrub with the Scrub'N'Clean Kit - Walls, rinse and wipe dry
  • Disinfects and helps inhibit mould growth
  • Protect the floor, drain and fixtures. Always test first
  • Floors, paths and paving: see remove algae, mould & mildew
Stone Gel+ 1 litre
STONE GEL+ · WALLS
1 L · 4 L
$61.00 View product

Why does mould grow on walls?

Mould and mildew grow where walls stay damp and poorly ventilated: shower walls, grout joints and silicone corners, bathroom and laundry walls, and shaded outdoor feature walls. Soap residue and body oils on shower walls feed the growth, leaving black, grey or green spots, mostly along the grout joints.

Cleaning helps remove the growth and staining, but it can return while the wall stays damp. Good ventilation, an exhaust fan and wiping walls down after showering help reduce regrowth.

TIP: once clean and completely dry, seal stone, grout and other porous surfaces with Aqua-Seal Gold+® for a natural look or Enhance'N'Seal for a colour enhanced look, to help reduce water absorption and make walls easier to keep clean.

Mould on a shower wall

Mould on a shower wall

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Skin (hard surface disinfectant only)
  • Non-recommended surfaces, and painted or timber surfaces nearby (protect them)
  • Mould inside wall cavities or behind tiles: get professional advice

What you'll need

  • Stone Gel+ (ready to use, no mixing)
  • Scrub'N'Clean Kit - Walls, sponge or white nylon pad
  • Narrow grout brush for the joints
  • Towels or plastic sheet to protect the floor, drain and fixtures
  • Sponge, spray bottle or handheld shower for rinsing, plus clean water
  • Clean cotton towels to wipe dry
  • Gloves and eye protection

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C. Work out of direct hot sun
  • Protect the floor, drain, tapware, fixtures and any non-recommended surfaces
  • Wipe or rinse off loose dirt first
  • Work in small sections you can keep wet for the full dwell time
  • Keep children and pets away until the area is rinsed

Step-by-step

Prepare → Treat → Remove + rinse
Protect and wipe down1Prepare

Protect and wipe down

Cover the floor, drain and tapware with towels or plastic, then wipe or rinse loose dirt off the wall.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try Stone Gel+ on a small, hidden spot to check ease of application, dwell time, colour stability and results.

Apply Stone Gel+ neat3Treat

Apply Stone Gel+ neat

Ready to use, no dilution. Pour onto a gloved hand, sponge or white nylon pad and smear evenly over the section of wall. Work top to bottom in small sections.

Allow at least 10 minutes dwell time4Treat

Allow at least 10 minutes dwell time

The cling gel stays on the wall. Don't allow the product to dry on the surface: add more Stone Gel+ to keep it wet and active.

Scrub the wall5Treat

Scrub the wall

Scrub with the Scrub'N'Clean Kit - Walls or a white nylon pad, top to bottom.

Scrub the grout joints6Treat

Scrub the grout joints

Use a narrow grout brush on dirty grout joints and corners.

Rinse and wipe dry7Remove + rinse

Rinse and wipe dry

Remove the dirty gel with a sponge, then rinse thoroughly with clean water from a sponge, spray or handheld shower. Wipe dry with clean towels.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the wall once it is fully dry and repeat the process as necessary.

How to use: Stone Gel+

Dilution None, use neat (ready to use)
Apply with Gloved hand, sponge or white nylon pad
Dwell time Minimum 10 minutes, keep wet
Surface temp. 4°C to 32°C
Pack sizes 1 L · 4 L

Why a cling gel for walls?

Liquid cleaners run straight down a wall. The high viscosity gel stays where you put it, so it gets the full 10 minutes dwell time on the mould and grout joints while it disinfects. No buckets or mixing.

Tips for the best result

  • Work top to bottom in small sections
  • Spend extra time on grout joints and corners, where mould starts
  • Run the exhaust fan and open a window while you work and afterwards
  • Squeegee or wipe shower walls after each use to help reduce regrowth
  • Mould on floors, paths or paving? See remove algae, mould & mildew
  • Badly stained grout may need re-colouring with Colour'N'Seal

Aftercare

Aqua-Seal Gold+

For a natural look: re-seal stone, grout and other porous surfaces with Aqua-Seal Gold+® once clean and completely dry.

Enhance'N'Seal

For a colour enhanced look: seal stone, grout and other porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles and grout. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Always test first. May dull or discolour some sensitive surfaces
  • Wear gloves and eye protection: causes serious eye damage. Avoid skin contact
  • Do NOT breathe mist, vapours or spray
  • Use when the surface is between 4°C and 32°C
  • Do NOT allow contact with non-recommended surfaces. Do NOT mix with other chemicals
  • May affect some dark grouts and grout colourants
  • Regular use of alkaline cleaners can affect sealers, coatings, grout colourants and floor finishes
  • Hard surface disinfectant only. Do NOT use on skin
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

The degree of success depends on the surface, how long the mould has been there, and whether the surface was sealed. Badly stained or discoloured grout may need re-grouting or re-colouring with Colour'N'Seal. Mould can return while walls stay damp.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp