HOW TO REMOVE SEALER RESIDUE FROM STONE, TERRAZZO AND TILES
Step-by-step instructions to help remove sealer residue from natural stone, encaustic, terrazzo and porcelain tiles, pavers and other sealed surfaces, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.
Pre-wet, scrub, pick up, rinse
Sealer that isn't wiped off in time can dry on the surface as shiny, sticky or blotchy patches. MicroScrub is a ready-to-use, non-acidic Nano Cream cleaner that helps remove surface sealer residue. It is formulated not to affect the penetrating sealer in the surface.
- MicroScrub: ready to use, non-acidic Nano Cream. No dilution
- Removes the surface residue only: the penetrating sealer stays in place
- Pour, scrub and rinse: no dwell time needed
- Don't let the product dry on the surface
- Always test first, especially on polished and dark surfaces
- Extreme heavy residue: use Strip-It, then reseal
What is sealer residue?
Penetrating sealers are designed to soak into the surface. Any excess left sitting on top, or not wiped off within the label time, can dry as a sticky, shiny, streaky or blotchy film.
This film can look patchy, catch dirt and make the surface harder to clean. Because it sits on top, it can usually be scrubbed off without disturbing the sealer that has penetrated the surface.
Suitable for
- Natural stone incl. acid-sensitive marble, limestone and travertine (test first)
- Terrazzo, encaustic and porcelain tiles
- Ceramic, concrete, pavers and masonry
- Floors and walls, indoors and outdoors
Where to use
- Domestic: homes, units, duplexes etc
- Commercial: hotels, shopping centres, restaurants, schools, aged care etc
Not for
- Extreme heavy residue: use Strip-It, then reseal
- Penetrating sealer in the surface: MicroScrub won't remove it
- Black or green pads on polished surfaces
What you'll need
- MicroScrub
- Scrub'N'Clean Kit, white nylon pad or scrub brush (never a black or green pad on polished surfaces)
- Grout brush for joints and edges
- Spray bottle or pump sprayer with clean water
- Broom, plus a wet vac (recommended) or mop
- Plenty of clean water and cotton towels
- Skin and eye protection
- Optional: slow-speed scrub machine for larger areas
Before you start
- Always do a test area first
- Surface temperature between 4°C and 32°C
- Work out of direct sun and wind so the product doesn't dry
- Take extra care on polished, soft and dark coloured stone and grout
- Keep children and pets away until the area is rinsed and dry
Step-by-step
Prepare → Treat → Remove + rinse
1Prepare
Prepare the area
Sweep, vacuum or wipe the surface to remove loose dirt and grit.
2Prepare
Do a test area first
VERY IMPORTANT
Try MicroScrub on a small, hidden spot. Check colour stability, polished or dark surfaces and grout, and how well the sealer residue lifts.
3Prepare
Lightly pre-wet
Slightly pre-wet the surface and grout joints with clean water. On walls, spray water from a spray bottle.
4Treat
Apply MicroScrub
Pour approx. 1–2 cups (250–500 mL) of MicroScrub onto the pre-wet surface. Use it as is: no dilution. On walls, apply it directly to a white nylon pad. Work in small sections.
5Treat
Scrub straight away
Scrub with a white nylon pad, scrub brush or scrub machine. No dwell time needed. Don't allow the product to dry on the surface: add a little water to keep it wet and active.
6Treat
Work the joints and edges
Work the grout joints, edges and corners with a grout brush where residue builds up.
7Remove + rinse
Pick up and rinse
Remove the dirty solution with a wet vac or mop, then rinse thoroughly with clean water and pick up the rinse water too.
8Remove + rinse
Check when dry, repeat if needed
Wipe dry with cotton towels and check the area once fully dry, in good light. Repeat as necessary.
How much MicroScrub?
| Use | Dilution | Amount |
|---|---|---|
| Floors | Use as is (do not dilute) | Approx. 1–2 cups (250–500 mL) per section, onto the pre-wet surface |
| Walls & vertical surfaces | Use as is | Apply directly to a white nylon pad after spraying the surface with water |
| As a booster | Add to the standing solution | Follow the cleaner or problem solver directions, then add MicroScrub just before scrubbing |
Tips for the best result
- Work in small sections and never let the product dry on the surface
- Pick up all of the dirty solution: residue left behind can dry back on
- Check the result once fully dry, in raking light
- Next time, wipe off excess sealer within the time on the label
- Extreme heavy residue: use Strip-It as per label, then reseal
- For other stains, see the Stain Removal Guide
Aftercare

For a natural look: if a porous surface needs (re)sealing, apply Aqua-Seal Gold+® once clean and fully dry, following the label.

For a colour enhanced look: apply Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.
Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles and pavers. Porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.
Precautions
- Read the entire label, SDS and technical bulletin before using
- Wear appropriate skin and eye protection
- Use when the surface temperature is between 4°C and 32°C
- Do not allow product to contact any non-recommended surfaces
- Take care on dark coloured grout or stone, and on polished or glossy surfaces
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Limitations
MicroScrub removes surface sealers, finishes and residue only. It will not remove penetrating sealers or deep-set stains below the surface. Polished and dark surfaces may scratch or dull: test first.
For extreme heavy sealer residue, use Strip-It as per label instructions. You must then re-apply sealer as per label instructions.
For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.
Important note
These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.


