HOW TO REMOVE INK, MARKER, PAINT & SILICONE

Step-by-step instructions for natural stone, porcelain, encaustic and terrazzo tiles, bricks, pavers, concrete and other surfaces, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Ink, paint & graffiti

Apply neat, dwell, scrub, rinse

Strip-It is a Professional Grade, heavy duty, multi-purpose remover. It stays wet for longer to break down tough residues and helps remove ink, marker, paint, graffiti and silicone from floors and walls.

  • Strip-It: ready to use, do NOT dilute
  • Minimum 30 minutes dwell, up to 2 hours (the longer the better)
  • Don't let it dry on the surface: add more to keep it wet
  • Floors: scrub with Strip'N'Clean Kit - Floors. Walls: brush on and work with Strip'N'Clean Kit - Walls
  • Scrape off thick silicone beads first
  • Solvent-based: ventilate well and wear gloves, eye protection and a mask
  • Always test first
Strip-It 4 litre
STRIP-IT
1 L · 4 L
$85.00 View product
XtremeClean+ 4 litre
XTREMECLEAN+ · RESIDUE
1 L · 4 L · 15 L
$51.00 View product

Why are ink, paint and silicone so hard to remove?

Inks, markers, spray paint and silicone are designed to stick. On porous surfaces such as natural stone, grout, concrete, bricks and pavers they can soak into the pores, so scrubbing with water or a general cleaner often just spreads them.

A heavy duty remover with a long dwell time softens and breaks down these residues so they can be scrubbed and rinsed away. Older and deeper marks may take more than one application.

FLOORS + WALLS: apply with a roller, mop, brush or sponge. On walls and graffiti, work from the bottom up and keep the surface wet, using Strip'N'Clean Kit - Walls.

Watch the video

Removing / Stripping Old Coatings & Sealers – Strip-It – Sealers Plus

Removing / Stripping Old Coatings & Sealers – Strip-It – Sealers Plus

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc
  • Industrial: warehouses, workshops, factories etc

Not for

  • Painted, waxed or sealed surfaces you want to keep: Strip-It will affect sealers, coatings, floor finishes, deck stains and painted surfaces
  • Mixing with other chemicals
  • Painted surfaces: it will affect the paint you want to keep

What you'll need

  • Strip-It (ready to use, do NOT dilute) in a plastic container
  • Plastic scraper for silicone beads
  • Roller, brush or sponge to apply
  • Strip'N'Clean Kit - Floors (floors) or Strip'N'Clean Kit - Walls (walls), white nylon pad or scrub brush
  • Wet vac (recommended), mop or sponge
  • XtremeClean+ for residue (optional)
  • Plenty of clean water and cotton towels
  • Chemical resistant gloves, eye protection and a suitable mask

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C
  • Use in a well ventilated area: open doors and windows, and wear a suitable mask
  • Protect painted, waxed and sealed surfaces, timber, skirting and fixtures nearby
  • Keep children, pets and anyone pregnant or nursing away from the area
  • The floor will get slippery: plan a safe way in and out

Step-by-step

Prepare → Treat → Remove + rinse
Prepare and ventilate1Prepare

Prepare and ventilate

Sweep or vacuum the area. Open doors and windows for good ventilation, protect nearby painted, waxed or sealed surfaces and put on gloves, eye protection and a suitable mask.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try Strip-It on a small, hidden spot to check ease of application, dwell time, colour stability and how well the ink, paint or silicone lifts.

Apply Strip-It neat3Treat

Apply Strip-It neat

Do NOT dilute. Pour Strip-It into a plastic container and, with a roller, mop, brush or sponge, carefully apply a liberal amount to a manageable area. Scrape off any thick silicone first. On walls, brush it on and keep it wet.

Dwell 30 min – 2 hours4Treat

Dwell 30 min – 2 hours

Allow a minimum dwell time of 30 minutes, up to 2 hours depending on the problem (the longer the better). Don't allow it to dry on the surface: add more Strip-It to keep it wet and active.

Scrub5Treat

Scrub

Scrub with a white nylon pad, scrub brush or scrub machine (slow speed scrubber for large areas).

Pick up the dirty solution6Remove + rinse

Pick up the dirty solution

Remove the dirty solution with a wet vac or mop.

Rinse thoroughly7Remove + rinse

Rinse thoroughly

Rinse thoroughly with clean water. To help with any residue, apply XtremeClean+ diluted 1:5 with water, scrub again, then rinse thoroughly.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the surface once dry and repeat the process as necessary. Ready for light traffic after 1 hour or once all fumes and vapours have dissipated.

How to use Strip-It

Product Strip-It: ready to use, solvent-based. Do NOT dilute.
Dwell time Minimum 30 minutes, up to 2 hours (the longer the better). Keep wet.
Coverage (neat) As a guide, 1 L of Strip-It used neat covers approx. 7–10 m², depending on the severity of the problem, how many times the process is repeated, surface porosity and texture, and site conditions.
Ink, paint & graffiti Older marks may need more than one application
Residue XtremeClean+ diluted 1:5 with water after rinsing, scrub, then rinse again
Re-seal After at least 48 hours drying. Test a new sealer or coating first

Tips for the best result

  • Remove fresh marks as soon as you can: they are easier to lift
  • Scrape thick silicone beads off with a plastic scraper before applying
  • Keep the product wet for the full dwell time, especially on walls and in the sun
  • Protect painted walls, window frames and fixtures next to the area
  • Ventilate well while you work and until all fumes have dissipated
  • For other stains, see the Stain Removal Guide

After stripping + aftercare

Aqua-Seal Gold+

For a natural look: re-seal porous surfaces with Aqua-Seal Gold+® after at least 48 hours drying (test first).

Enhance'N'Seal

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead, after at least 48 hours drying. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles, pavers and concrete. Porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Wear appropriate gloves, skin and eye protection: causes serious eye damage
  • Do NOT breathe in fumes or vapours: wear an appropriate mask. Use in a well ventilated area
  • Avoid contact during pregnancy or while nursing
  • Use when the surface temperature is between 4°C and 32°C
  • Do NOT allow contact with painted or waxed surfaces. Will affect sealers, coatings, floor finishes, deck stains and painted surfaces
  • Do NOT mix with other chemicals
  • The floor will get slippery during the process. Take appropriate precautions to prevent slips and falls
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

Strip-It helps remove ink, marker, paint, graffiti and silicone. Some pigments can stain deep into porous surfaces and may leave a shadow. Removal of thick or multiple coatings may require multiple applications of Strip-It. Allow at least 48 hours drying time before applying any sealers, coatings or floor finishes.

For stains, see the Stain Removal Guide and our Problem Solvers.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp