HOW TO REMOVE RUST, IRON, METAL & BORE WATER STAINS

Step-by-step instructions for all natural stone including marble, limestone and travertine, porcelain, encaustic and terrazzo tiles, concrete, pavers and bricks, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Rust & metal stains

Spray, dwell, scrub, rinse

Rust Away is a Professional Grade, pH neutral, non-acidic rust, iron, bore and metal oxide cleaner and remover. Its fast acting, non-etch formula helps remove rust and rust water, bore water, iron fertiliser and metal marks, shavings and scrapes, including on acid-sensitive surfaces.

  • Ready to use: do NOT dilute. Spray or pour onto the stain
  • The stain turns purple as Rust Away reacts with it
  • Dwell 5–10 minutes, never longer than 10. Don't let it dry on the surface
  • Scrub, blot up, then rinse thoroughly
  • pH neutral, non-acidic: ideal for acid-sensitive surfaces. Always test first
  • Only works on iron-based stains
  • Keep away from non-recommended surfaces
Rust Away 1 litre
RUST AWAY
250 mL · 1 L · 4 L
$56.00 View product

What causes rust and metal stains?

Iron reacts with water and air to form orange-brown iron oxide. On porous surfaces such as natural stone, concrete, pavers and grout, it soaks in from metal pot plant stands and outdoor furniture, nails and metal shavings, iron-rich fertilisers, rust water and bore water used for irrigation. Some stone also contains natural iron that can show as rust spots.

Acid rust removers can etch marble, limestone, travertine, terrazzo and concrete. Rust Away is pH neutral and non-acidic, so it helps remove the stain without etching the surface. As it works, the stain turns purple; any purple residue lightens over a few days.

TIP: once the stain is removed and the surface is completely dry, seal porous surfaces with Aqua-Seal Gold+® for a natural look or Enhance'N'Seal for a colour enhanced look, to help reduce future staining and make cleaning easier.

Before & after

Before & after

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Stains that are not iron or metal based
  • Stains covered by a sealer or coating: remove it with Strip-It first

What you'll need

  • Rust Away
  • Spray bottle, or plastic bucket plus clean sponge, roller or mop to apply
  • Scrub'N'Clean Kit, white nylon pads or scrub brush
  • Paper towels or absorbent cloths (wet vac for large areas)
  • Hose, or bucket and mop, plus plenty of clean water
  • A watch for timing
  • Mask, gloves, eye, skin and foot protection

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 28°C
  • Work in a well ventilated area
  • Sweep, vacuum or wipe the surface
  • Remove any sealer or coating over the stain first
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Sweep the surface1Prepare

Sweep the surface

Sweep, vacuum or wipe the surface. Move metal furniture and pot stands away.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try Rust Away on a small, hidden spot to check ease of application, dwell time, colour stability and the result.

Spray or pour on Rust Away3Treat

Spray or pour on Rust Away

Ready to use, do NOT dilute. Spray or pour Rust Away directly onto the stain.

Watch it turn purple4Treat

Watch it turn purple

The stain will start to turn purple as Rust Away reacts with the iron. This shows it is working.

Allow 5–10 minutes dwell time5Treat

Allow 5–10 minutes dwell time

Allow to dwell for 5–10 minutes depending on the severity. Do NOT dwell longer than 10 minutes, and don't let it dry: add more Rust Away to keep it wet and active.

Scrub6Treat

Scrub

After the dwell time, scrub with a white pad or scrub brush, or a Scrub'N'Clean Kit.

Blot up and rinse7Remove + rinse

Blot up and rinse

Remove the dirty solution with paper towels or absorbent cloths (or a wet vac on large areas), then rinse thoroughly with clean water and dry the surface.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the area once dry and repeat as necessary. Any purple residue will lighten over a few days.

Coverage: Rust Away

Coverage: spot treatment – use as required per stain / spot. The amount needed depends on the size and severity of the stain and the porosity of the surface.

Ready to use, no dilution.

Stains Rust Away helps remove

  • Rust and rust water
  • Bore water stains
  • Iron fertiliser
  • Metal marks, scrapes and shavings
  • Metal furniture and pot stand marks
  • Iron oxide in stone

Tips for the best result

  • Treat rust early, before it soaks deeper
  • Never exceed 10 minutes dwell time: long dwell times may cause slight dullness or colour change on some sensitive surfaces
  • Keep the stain wet with more product rather than letting it dry
  • Put saucers or feet under metal pot stands and furniture to help reduce new marks
  • Not iron based? Use the Product Selector to find the right product
  • For other stains, see the Stain Removal Guide

Aftercare

Aqua-Seal Gold+

For a natural look: seal porous surfaces with Aqua-Seal Gold+® once clean and completely dry, to help reduce staining and make cleaning easier.

Enhance'N'Seal

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles, concrete and pavers. Porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Wear appropriate gloves, skin and eye protection: may cause an allergic skin reaction
  • Do NOT breathe fumes or vapours: wear an appropriate mask and use in a well ventilated area
  • Do NOT eat, drink or smoke when using this product
  • Use when the surface temperature is between 4°C and 28°C
  • Do NOT allow contact with non-recommended surfaces
  • Do NOT mix with other chemicals
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

Rust Away only works on iron-based stains and marks. It will not work if the stain is covered by a sealer or coating: remove it with Strip-It first, then use Rust Away. For deep-set stains try Poultice Plus. The degree of success depends on the surface, the stain and how long it has been in place.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp