HOW TO REMOVE SOAP SCUM FROM TERRAZZO & ENCAUSTIC TILES

Step-by-step instructions for terrazzo and encaustic tiles plus other acid-sensitive surfaces, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Soap scum · No acids

Pre-wet, pour, scrub, rinse

MicroScrub is a powerful, Professional Grade Nano-Cream cleaner that is non-flammable and contains no VOCs or acids. Its fine nano-abrasive helps remove light soap scum, mineral deposits and grime from acid-sensitive surfaces without the etching risk of acid cleaners, and it is formulated not to affect penetrating (impregnating) sealers.

  • Ready to use Nano-Cream: no dilution. Pour, scrub and rinse
  • Non-acidic, no VOC: for acid-sensitive surfaces (test first)
  • Pour approx. 1–2 cups (250–500 mL) onto the pre-wet surface
  • No dwell time needed. Don't let it dry on the surface: add a little water
  • Pick up with a wet vac or mop, then rinse thoroughly
  • Take care on polished, glossy and dark coloured surfaces
  • Shower walls? See Remove Soap Scum from Walls (Stone Gel+), also for terrazzo and encaustic walls
MicroScrub
MICROSCRUB
250 mL · 1 L
$39.00 View product

What is soap scum?

Soap scum is the cloudy, greyish-white film that builds up when soap, body oils and minerals in hard water combine and dry on shower and bathroom surfaces. Over time it dulls the surface and holds dirt.

WHY NON-ACIDIC? Terrazzo and encaustic tiles are cement based and can etch with acidic soap scum removers. MicroScrub contains no acids. Shower walls? See Remove Soap Scum from Natural Stone Walls (also for terrazzo and encaustic walls).

Watch the video

MicroScrub – How To Use – Sealers Plus

MicroScrub – How To Use – Sealers Plus

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Deep-set stains or contaminants below the surface
  • Etch marks or dull, damaged polish: it won't restore polish

What you'll need

  • MicroScrub
  • Scrub'N'Clean Kit, white nylon pad, scrub brush or scrub machine
  • Broom and vacuum
  • Spray bottle or pump sprayer with clean water
  • Grout brush for the joints
  • Wet vac (recommended) or mop
  • Bucket, plenty of clean water and cotton towels
  • Skin and eye protection

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C
  • Work out of direct sun so the product doesn't dry
  • Take extra care on polished, glossy and dark coloured stone and grout
  • Use a white nylon pad only on polished surfaces
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Prepare the area1Prepare

Prepare the area

Sweep, vacuum or wipe the surface to remove loose dirt and debris.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try MicroScrub on a small, hidden spot. Check colour stability, polish and dark grouts. Polished and dark surfaces may scratch or dull.

Lightly pre-wet3Prepare

Lightly pre-wet

Slightly pre-wet the surface and grout joints with clean water. On walls, spray water from a spray bottle.

Apply MicroScrub4Treat

Apply MicroScrub

Pour approx. 1–2 cups (250–500 mL) of MicroScrub onto the pre-wet surface. On walls, apply it directly to a white nylon pad. Work in small sections.

Scrub straight away5Treat

Scrub straight away

Scrub with a white nylon pad, scrub brush or scrub machine: no dwell time required. Don't allow the product to dry on the surface: add a little water to keep it wet and active.

Scrub the grout joints6Treat

Scrub the grout joints

Work the grout joints and edges with a grout brush.

Pick up and rinse7Remove + rinse

Pick up and rinse

Remove the dirty solution with a wet vac or mop, then rinse thoroughly with clean water and pick up the rinse water too.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the area once it is fully dry. Repeat as necessary until you're happy with the result.

How much? MicroScrub

Use How Amount
Floors Pour onto the pre-wet surface, scrub straight away 1–2 cups (250–500 mL) per section
Walls & vertical surfaces Spray water on the wall, apply to a white nylon pad, scrub Enough to keep the pad loaded
Booster Add to the standing solution of a cleaner or problem solver just before scrubbing As needed

Use as is: do not dilute. No dwell time required.

Tips for the best result

  • Treat light soap scum, mineral deposits and grime early: the older it is, the harder it can be to remove
  • Heavy build-up or residue older than 10 days may need several applications
  • Use a white nylon pad only. Never a black or green pad on polished surfaces
  • Work in small sections and keep the surface wet and active
  • Boost a cleaner: add MicroScrub to the standing solution of any Sealers Plus cleaner just before scrubbing
  • Walls and splashbacks: Stone Gel+ clings to vertical surfaces. See the wall guide
  • Squeegee the shower after use to help reduce build-up

Aftercare

Aqua-Seal Gold+

For a natural look: re-seal porous surfaces with Aqua-Seal Gold+® once clean and completely dry, when water starts to absorb quicker than before.

Enhance'N'Seal

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+

XtremeClean+: Half yearly or as needed heavy-duty clean.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: terrazzo and encaustic tiles and grout. Use the Product Selector to check the right sealer for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Wear appropriate skin and eye protection
  • Use when the surface temperature is between 4°C and 32°C
  • Do NOT allow product to contact any non-recommended surfaces
  • Take care on dark coloured grout or stone, and on polished or glossy surfaces
  • Keep floors dry to help prevent slips and falls
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

MicroScrub will not remove deep-set stains or contaminants below the surface, etch marks or damaged polish. It removes surface sealers and finishes only, not penetrating sealers. Heavy build-up may need multiple applications.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp