HOW TO REMOVE GROUT HAZE FROM ENCAUSTIC & TERRAZZO TILES
Step-by-step instructions for encaustic and terrazzo tiles, Fibonacci Terrazzo and other acid-sensitive surfaces, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.
Pre-wet, pour, scrub, rinse
MicroScrub is a powerful, Professional Grade Nano-Cream cleaner that is non-flammable and contains no VOCs or acids. Its fine nano-abrasive helps remove light grout haze (including light epoxy grout haze) from acid-sensitive surfaces without the etching risk of acid cleaners, and it is formulated not to affect penetrating (impregnating) sealers.
- Ready to use Nano-Cream: no dilution. Pour, scrub and rinse
- Non-acidic, no VOC: for acid-sensitive surfaces (test first)
- Pour approx. 1–2 cups (250–500 mL) onto the pre-wet surface
- No dwell time needed. Don't let it dry on the surface: add a little water
- Pick up with a wet vac or mop, then rinse thoroughly
- Take care on polished, glossy and dark coloured surfaces
What is grout haze?
Grout haze is the powdery cement residue left on tiles and stone after grouting when the clean-up during installation isn't thorough. The longer it stays, the harder it becomes to remove. It leaves the surface looking dull and dirty and can start to catch dirt.
Suitable for
- Encaustic cement tiles
- Terrazzo tiles incl. Fibonacci Terrazzo
- Acid-sensitive stone e.g. marble, limestone, travertine
- Grout: floors and walls, indoors and outdoors
Where to use
- Domestic: homes, units, duplexes etc
- Commercial: hotels, shopping centres, restaurants, schools, aged care etc
Not for
- Heavy cement grout haze on ceramic or porcelain tiles: use OxiTreat+
- Deep-set stains or contaminants below the surface
- Etch marks or dull, damaged polish: it won't restore polish
What you'll need
- MicroScrub
- Scrub'N'Clean Kit, white nylon pad, scrub brush or scrub machine
- Broom and vacuum
- Spray bottle or pump sprayer with clean water
- Grout brush for the joints
- Wet vac (recommended) or mop
- Bucket, plenty of clean water and cotton towels
- Skin and eye protection
Before you start
- Always do a test area first
- Surface temperature between 4°C and 32°C
- Work out of direct sun so the product doesn't dry
- Take extra care on polished, glossy and dark coloured stone and grout
- Use a white nylon pad only on polished surfaces
- Keep children and pets away until the area is rinsed and dry
Step-by-step
Prepare → Treat → Remove + rinse
1Prepare
Prepare the area
Sweep, vacuum or wipe the surface to remove loose dirt and debris.
2Prepare
Do a test area first
VERY IMPORTANT
Try MicroScrub on a small, hidden spot. Check colour stability, polish and dark grouts. Polished and dark surfaces may scratch or dull.
3Prepare
Lightly pre-wet
Slightly pre-wet the surface and grout joints with clean water. On walls, spray water from a spray bottle.
4Treat
Apply MicroScrub
Pour approx. 1–2 cups (250–500 mL) of MicroScrub onto the pre-wet surface. On walls, apply it directly to a white nylon pad. Work in small sections.
5Treat
Scrub straight away
Scrub with a white nylon pad, scrub brush or scrub machine: no dwell time required. Don't allow the product to dry on the surface: add a little water to keep it wet and active.
6Treat
Scrub the grout joints
Work the grout joints and edges with a grout brush.
7Remove + rinse
Pick up and rinse
Remove the dirty solution with a wet vac or mop, then rinse thoroughly with clean water and pick up the rinse water too.
8Remove + rinse
Check when dry, repeat if needed
Check the area once it is fully dry. Repeat as necessary until you're happy with the result.
How much? MicroScrub
| Use | How | Amount |
|---|---|---|
| Floors | Pour onto the pre-wet surface, scrub straight away | 1–2 cups (250–500 mL) per section |
| Walls & vertical surfaces | Spray water on the wall, apply to a white nylon pad, scrub | Enough to keep the pad loaded |
| Booster | Add to the standing solution of a cleaner or problem solver just before scrubbing | As needed |
Use as is: do not dilute. No dwell time required.
Tips for the best result
- Treat light grout haze (including light epoxy grout haze) early: the older it is, the harder it can be to remove
- Heavy build-up or residue older than 10 days may need several applications
- Use a white nylon pad only. Never a black or green pad on polished surfaces
- Work in small sections and keep the surface wet and active
- Boost a cleaner: add MicroScrub to the standing solution of any Sealers Plus cleaner just before scrubbing
- Next installation: add Haze Away to the final grout wash to help reduce haze
Aftercare

For a natural look: re-seal porous surfaces with Aqua-Seal Gold+® once clean and completely dry, when water starts to absorb quicker than before.

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

XtremeClean+: Half yearly or as needed heavy-duty clean.
Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: encaustic and terrazzo tiles and grout. Use the Product Selector to check the right sealer for your surface and finish.
Precautions
- Read the entire label, SDS and technical bulletin before using
- Wear appropriate skin and eye protection
- Use when the surface temperature is between 4°C and 32°C
- Do NOT allow product to contact any non-recommended surfaces
- Take care on dark coloured grout or stone, and on polished or glossy surfaces
- Keep floors dry to help prevent slips and falls
- WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.
Limitations
MicroScrub will not remove deep-set stains or contaminants below the surface, etch marks or damaged polish. It removes surface sealers and finishes only, not penetrating sealers. Heavy build-up may need multiple applications.
For other stains and problems, see our Problem Solvers and the Stain Removal Guide.
For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.
Important note
These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.


