HOW TO REMOVE LIGHT SOAP SCUM & HARD WATER DEPOSITS

Step-by-step instructions for shower and bathroom porcelain, ceramic, encaustic and terrazzo tiles, natural stone and grout, from the team who make Sealers Plus Professional Grade products in Kurnell, NSW.

Problem solver · Light soap scum

Dilute, dwell, boost, scrub, rinse

XtremeClean+ is a Professional Grade, non-acidic, high alkaline heavy duty cleaner, degreaser and commercial grade disinfectant. It helps remove light soap scum, body oils, grime and mildew from showers and bathrooms, including acid-sensitive terrazzo, encaustic tiles and natural stone. Add MicroScrub to the standing solution for light hard water marks.

  • Dilute from 1:20 (200 mL to 4 L) up to 1:5 for stubborn build-up
  • Non-acidic: suits acid-sensitive surfaces. Always test first
  • Minimum 10 minutes dwell time. Don't let it dry on the surface
  • Boost with MicroScrub just before scrubbing
  • Scrub, then rinse thoroughly
  • Heavy build-up on acid-resistant tiles: see heavy soap scum
  • Keep away from non-recommended surfaces
XtremeClean+ 4 litre
XTREMECLEAN+
4 L
$51.00 View product
MicroScrub
MICROSCRUB · BOOSTER
250 mL · 1 L
$39.00 View product

What is soap scum?

Soap scum is the dull, greyish-white film that builds up in showers and around baths. Soap and body products react with the minerals in tap water and stick to tiles, grout and glass with body oils and dirt. Hard water marks are the chalky mineral spots left behind as water dries.

Light build-up responds to a strong alkaline clean with plenty of dwell time and scrubbing. Heavy, long-standing deposits on acid-resistant tiles may need an acid cleaner, which is not suitable for marble, limestone, travertine, terrazzo or encaustic tiles.

WHICH PAGE? Light build-up, any surface: this page. Heavy deposits on ceramic / porcelain: heavy soap scum. Polished stone: natural stone. Terrazzo & encaustic: terrazzo & encaustic.

Before & after

Before & after

Suitable for

Where to use

  • Domestic: homes, units, duplexes etc
  • Commercial: hotels, shopping centres, restaurants, schools, aged care etc

Not for

  • Aluminium, metal mosaics, anodised or galvanised metal
  • Use undiluted: it may dull or discolour some surfaces

What you'll need

  • XtremeClean+
  • MicroScrub
  • Scrub'N'Clean Kit, white nylon pads, scrub brush or grout brush
  • Plastic bucket, measuring jug and clean water
  • Sponge or mop to apply
  • Hand shower, wet vac or mop plus plenty of clean water for rinsing
  • Gloves, eye, skin and foot protection

Before you start

  • Always do a test area first
  • Surface temperature between 4°C and 32°C
  • Ventilate the bathroom
  • Remove bottles, mats and loose debris
  • Coloured grout and sealed surfaces: start at the weakest dilution that does the job
  • Keep children and pets away until the area is rinsed and dry

Step-by-step

Prepare → Treat → Remove + rinse
Clear the area1Prepare

Clear the area

Remove bottles and mats, then sweep or wipe loose hair and debris off the surface.

Do a test area first2Prepare

Do a test area first

VERY IMPORTANT
Try the solution on a small, hidden spot to check dilution, colour stability and the result.

Dilute XtremeClean+3Treat

Dilute XtremeClean+

Always add XtremeClean+ to clean water. Light soap scum: 200 mL to 4 L (1:20). Stubborn build-up: 1:10 or 1:5.

Apply4Treat

Apply

Carefully apply the diluted solution with a sponge or mop. Work in sections.

Allow 10 minutes dwell time5Treat

Allow 10 minutes dwell time

Allow a minimum dwell time of 10 minutes. Don't allow the product to dry on the surface: add more diluted product to keep it wet and active.

Boost with MicroScrub and scrub6Treat

Boost with MicroScrub and scrub

Add MicroScrub to the standing solution, then scrub with a white nylon pad, scrub brush or Scrub'N'Clean Kit. Use a grout brush on the joints.

Rinse thoroughly7Remove + rinse

Rinse thoroughly

Remove the dirty solution with a wet vac or mop, then rinse thoroughly with clean water.

Check when dry, repeat if needed8Remove + rinse

Check when dry, repeat if needed

Check the area once it is fully dry and repeat as necessary.

Dilution rates: XtremeClean+

Use Ratio Add to 4 L water Makes
Light cleaning only (not a disinfecting dilution) 1:40 100 mL 4.1 L
General cleaning, degreasing & disinfecting 1:20 200 mL 4.2 L
Moderate cleaning, degreasing & disinfecting 1:10 400 mL 4.4 L
Deep cleaning, degreasing & disinfecting 1:5 800 mL 4.8 L
Heavy duty cleaning, stripping porcelain wax & floor finishes 1:2 2 L 6 L

Always add XtremeClean+ to clean water to prevent splashing. Never use undiluted. For disinfecting use 1:20 or stronger.

Keep soap scum away

  • Squeegee or towel-dry shower walls and floors after use
  • Ventilate the bathroom to help reduce mould and mildew
  • Clean weekly with a pH neutral cleaner so build-up stays light
  • Seal porous stone and grout to help make cleaning easier

Tips for the best result

  • Treat build-up early: light soap scum is much easier to remove
  • Warm the room first: soap scum softens faster
  • Keep the surface wet for the whole dwell time
  • Rinse well: leftover cleaner can leave a film
  • Squeegee after every shower to help reduce new build-up
  • For other stains, see the Stain Removal Guide

Aftercare

Aqua-Seal Gold+

For a natural look: seal porous surfaces with Aqua-Seal Gold+® once clean and completely dry, to help reduce staining and make cleaning easier.

Enhance'N'Seal

For a colour enhanced look: seal porous surfaces with Enhance'N'Seal instead. The colour change is permanent: always test first.

EzyClean+

EzyClean+: Daily / Weekly cleaning, pH neutral.

Stone Wash+

Stone Wash+: Quarterly deep clean for natural stone and terrazzo.

Aqua-Seal Gold+® and Enhance'N'Seal are for porous surfaces only: natural stone, encaustic and terrazzo tiles and grout. Ceramic and porcelain tiles take a different sealer: use the Product Selector to find the right one for your surface and finish.

Precautions

  • Read the entire label, SDS and technical bulletin before using
  • Wear appropriate gloves, skin and eye protection. Do NOT kneel in product or allow skin contact
  • Do not breathe fumes, mist, vapours or spray
  • Use when the surface temperature is between 4°C and 32°C
  • Do NOT allow contact with non-recommended surfaces (e.g. aluminium, metal mosaics, anodised or galvanised metal)
  • Do NOT mix with other chemicals
  • May affect some dark grouts and grout colourants. Do NOT use undiluted: it may dull or discolour some surfaces
  • Regular use of high alkaline cleaners can affect the performance of sealers, coatings, grout colourants and floor finishes
  • WASH UNDERSIDE OF SHOES BEFORE STEPPING ONTO OTHER AREAS.

Limitations

XtremeClean+ helps remove light soap scum and hard water marks. Heavy, long-standing deposits on acid-resistant tiles may need OxiTreat+ (not for natural stone or acid-sensitive surfaces). It will not remove etch marks or restore polish. Badly stained grout may need re-grouting or re-colouring with Colour'N'Seal.

For other stains and problems, see our Problem Solvers and the Stain Removal Guide.

For additional options, contact the Sealers Plus Technical Services Team at support@sealersplus.com.au or call +61 2 9521-4000 with details of the problem you are addressing.

Important note

These recommendations are general guidelines for problem solving. Actual dilution ratios and cleaning requirements may vary depending on the surface, the use, the amount and the method of application.
Read the entire Product Label, SDS and Technical Bulletin before using any product.
ALWAYS TEST A SMALL AREA to determine the ease of application, dilution, dwell time and desired results.
Keep the surface clean and dry to reduce the possibility of slip-fall accidents.
Chat on WhatsApp